User manual SMEG CB51VMY

[. . . ] The installation must be carried out by a specialised technician. WARNING: Keep the product's standard installation nozzles and the "regulated for gas" label, since reconversion from METHANE gas to GPL gas could be necessary in the future. In the case of reconversion to GPL gas, the conversion procedure is identical to that described below for METHANE gas. KIT CONTENTS The contents of the methane gas transformation kit are listed below: · · · NOZZLES FOR METHANE GAS. LABEL "REGULATED FOR GAS" TRANSFORMATION). (TO BE APPLIED AFTER THE 10 Instructions for the installer GAS MAINS CONNECTION The product must be connected to the methane gas mains by means of a standards-compliant rubber or flexible steel hose. [. . . ] Screw the connector (A) inserting the sealing gasket (B) at the barbecue inlet connector (C); see the drawing at the side. Depending on the diameter of the hose, you may or may not need to attach smaller connector (F) to the connector (A) attached previously. Push the hose (E) onto the connector (A) or (F) and secure it to the connector by means of a clamp (D). Verify that the following conditions are met: · the hose is fixed to the hose connection with safety clamps. · it is possible to inspect the entire length of the hose (max 1. 5 m). · no part of the hose is in contact with the hot walls (max. · the hose is not under traction or tension and has no tight curves or twists. · the hose is not in contact with sharp objects or sharp corners. · if the hose is not perfectly airtight and leaks gas, do not try to repair it; replace it with a new tube. · verify that the hose is not beyond its life cycle. 5 Replace the rear part, screwing it into place with the holding screws. REPLACING RAPID - AUXILIARY BURNER NOZZLES (ONLY ON MODELS BQ6130T - BQ6130S - BQ6130) 1 2 3 4 Remove the grids, the caps and the flamespreader crowns; Using a 7mm wrench unscrew the nozzle of the burner. Change the nozzles according to the table provided above. Replace the burners, the caps and the flamespreader crowns correctly in their appropriate positions. 1 1 2 14 Instructions for the installer PRIMARY AIR ADJUSTMENT Carry out the following operations for every burner present in the barbecue compartment: PRIMARY AIR ADJUSTMENT WITH "SINGLE PARALLEL FLAME" BURNERS 1 Loosen the adjustment screw A of the air regulation sleeve. 2 Turn the registration sleeve B to the position that corresponds to the type of gas to be used according to the table below. 3 Tighten the adjustment screw making sure that the distance X is correct (See table below). PRIMARY AIR ADJUSTMENT WITH "DUAL PARALLEL FLAME" BURNERS 1 Loosen the adjustment screw A of the air regulation sleeve. 2 Extract or insert the registration sleeve B to the position that corresponds to the type of gas to be used according to the table below. 3 Tighten the adjustment screw making sure that the distance X is correct (See table below). A B X X= METHANE (N) Single parallel flame burners 1. 5 mm G30/G31 (GPL) Single parallel flame burners 4 mm METHANE (N) Dual parallel flame burners 4 mm G30/G31 (GPL) Dual parallel flame burners 8 mm 15 Instructions for the installer BURNER MINIMUM ADJUSTMENT CONVERSION FROM GPL GAS TO METHANE GAS Carry out the following operations on all the gas taps. Make sure that the by-pass inside is fully screwed in. [. . . ] Make sure that the by-pass inside is fully screwed in. Use a screw driver inside the tap rod or at the side (See the drawing at the side). Turn the by-pass according to the table BURNER, NOZZLE AND GAS CONSUMPTION CHARACTERISTICS (see page 11). When the adjustments are completed, insert the knob and light the relative burner bringing it to the minimum position . [. . . ]