User manual SMEG CB81VGY

[. . . ] Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. Do not flamb under the range hood; risk of fire This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. 650 mm min. MAINTENANCE Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. Clean and/or replace the Filters after the specified time period (Fire hazard). [. . . ] Clean the hood using a damp cloth and a neutral liquid detergent. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. EN 1 13 3 CHARACTERISTICS Dimensions min. 861 -max. 1146 696 120 20 898 350 150 698 290 EN 1 14 4 650 min. 306 90 130 Components Ref. 1 2 2. 1 2. 2 7. 1 7. 1a 7. 1b 8a 8b 9 10 14 14. 1 15 24 25 Ref. 11 12c 12e 12f 12g 12h 12q 21 22 23 Q. ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Telescopic Chimney comprising: 1 Upper Section 1 Lower Section 1 Telescopic frame complete with extractor, consisting of: 1 Upper frame 1 Lower frame 1 Right Air Outlet Grill 1 Left Air Outlet Grill 1 Reducer Flange 150-120 mm 1 Damper (Optional) 1 Hood Body Air Outlet Extension Piece consisting of two Half Shells(Optional) 1 Air Outlet Connection Extension 1 Air Outlet Connection 1 Junction box Pipe clamps (not included) Q. ty Installation Components 4 Wall Plugs 10 6 Screws 2, 9 x 6, 5 2 Screws 2, 9 x 9, 5 2 Screws M4 x 80 4 Screws M6 x 80 4 Screws 5, 2 x 70 4 Screws 3, 5 x 9, 5 1 Drilling template 8 6. 4 mm int. dia washers 4 M6 nuts Q. ty Documentation 1 Instruction Manual 21 23 22 7. 1a 12g 7. 1 11 12h 15 14. 1 7. 1b 9 12c 2. 1 2 2. 2 8b 8a 12e 24 25 12c 12c 1 12f 22 12q EN 1 15 5 INSTALLATION Drilling the Ceiling/shelf and fixing the frame DRILLING THE CEILING/SHELF Use a plumb line to mark the centre of the hob on the ceiling/support shelf. Place the drilling template 21 provided on the ceiling/support shelf, making sure that the template is in the correct position by lining up the axes of the template with those of the hob. Mark the centres of the holes in the template. Drill the holes at the points marked: For concrete ceilings, drill for plugs appropriate to the screw size. Before fixing the hood canopy to the frame: Screw the 2 screws 12f half way into the holes provided in the sides of the bottom of the frame. Remove the grease filters from the hood canopy. Lift the hood canopy and engage the screws 12f in the slots (A) as far as they will go. Working from below, fix the hood canopy to the frame (B), using the 4 screws 12q and 4 washers 22 provided, then tighten all the screws securely. 12c 8b 8a 12f 12q 22 B A EN 1 18 8 ELECTRICAL CONNECTION Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. Place the connectors in the junction box 24 and close it using the 2 screws 12e (2, 9 x 9, 5) provided. Fix the junction box to the hood body using the 2 screws 12c (2, 9 x 6, 5) provided. For the recirculation version, fit the activated carbon odour filter. Refit the grease filters. 24 12e 12c Cmd EN 1 19 9 USE L S V1 V2 V3 L S V1 V2 V3 Light Led Motor Speed Intensive Switches the lighting system on and off. Switches the extractor motor on and off at low speed. [. . . ] Switches the extractor motor on and off at low speed. Used to provide a contin-uos and silent air change in the presence of light cooking vapours. Medium speed, suitable for most operating conditions given the optimum treated air flox/noise level ratio. Maximum speed, used for eliminating the highest cooking vapour emission, including long periods. EN 2 20 0 MAINTENANCE Grease filters CLEANING METAL SELF- SUPPORTING GREASE FILTERS The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. [. . . ]