User manual SMEG CB91VGY

[. . . ] 30 MANUTENO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 2 2 RECOMMENDATIONS AND SUGGESTIONS The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. INSTALLATION The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. The minimum safety distance between the cooker top and the extractor hood is 650 mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation). [. . . ] Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. EN 3 3 CHARACTERISTICS Dimensions Min 780 700 Max 1070 132 90 Min. 500mm 650mm 310 70 350 150 650 290 36 EN 4 4 Components Ref. 1 2 2. 1 2. 2 7. 1 7. 1a 7. 1b 8a 8b 9 10 14. 1 15 24 25 26 27 Ref. 11 12c 12e 12f 12g 12h 12q 21 22 23 Q. ty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 Q. ty 4 6 2 2 4 4 4 1 8 4 Product Components Hood Canopy complete with: Controls, Lights, Filters Telescopic chimney made up of: Upper chimney Lower chimney Telescopic frame complete with Suction fan, made up of: Upper frame Lower frame Rh Air Outlet Directional Grille Lh Air Outlet Directional Grille Reduction flange 150-120 mm Dumper Air Outlet Connector Extension Air Outlet Connector Connection box Pipe clamps (not included) Cable clamps Finishing plug Installation Components Wall Plugs 10 Screws 2, 9 x 6, 5 Screws 2, 9 x 9, 5 Screws M4 x 80 Screws M6 x 80 Screws 5, 2 x 70 Screws 3, 5 x 9, 5 Drilling template 6. 4 mm int. dia washers M6 nuts 21 23 22 11 12h 7. 1a 12g 7. 1 14. 1 10 7. 1b 12c 2. 1 2 2. 2 8b 8a 12e 24 9 25 26 27 15 12c 1 12c 12f 22 12q Q. ty Documentation 1 Instruction booklet EN 5 5 INSTALLATION Drilling the Ceiling/shelf and fixing the frame DRILLING THE CEILING/SHELF Use a plumb line to mark the centre of the hob on the ceiling/support shelf. Place the drilling template 21 provided on the ceiling/support shelf, making sure that the template is in the correct position by lining up the axes of the template with those of the hob. Mark the centres of the holes in the template. Drill the holes at the points marked: For concrete ceilings, drill for plugs appropriate to the screw size. For hollow brick ceilings with wall thickness of 20 mm: drill 10 mm(immediately insert the Dowels 11 supplied). Push fit the assembled hood body extension piece 14 onto the air outlet (if necessary). Push fit connection 15 onto the hood body extension piece 14 or directly onto the hood body. Insert the connection extension pieces laterally 14. 1 in connection 15. Should the central reinforcing piece of the frame somehow interfere the chimney air outlet grille, it is possible to unscrew it and to place it in another screw hole set. 15 14. 1 14 Flue assembly - Mounting the hood body 12c Position the upper chimney section and fix the upper part to the frame using the 2 screws 12c (2, 9 x 6, 5) provided. Similarly, position the lower chimney section and fix the lower part to the frame using the 2 screws 12c (2, 9 x 6, 5) provided. Recirculation version Make sure that the outlet of the extension pieces 14. 1 is horizontally and vertically aligned with the chimney outlets. Otherwise, remove the lower chimney and adjust the position by inverting the extension pieces for air outlet connection 14. 1 or by cutting the hood body extension piece 14 (if any) along one of the chases destined to the predetermined extension lengths. Replace then the elements as earlier described. Fit the directional grids 8a - 8b in their housings making sure that the directional symbols are towards the top. Also make sure that they are correctly inserted in the connection extension pieces 14. 1. Before fixing the hood canopy to the frame: Screw the 2 screws 12f half way into the holes provided in the sides of the bottom of the frame. [. . . ] This speed is timed to run for 10 minutes. At the end of this time the system will Flashing. automatically return to the speed set before. Suitable to deal with maximum levels of cooking fumes, it is deactivated by pressing any one of the Speed buttons (T1-T2-T3). [. . . ]