User manual SMEG CBE54

[. . . ] 9 CLEANING AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 POSITION NEAR THE COUNTER TOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ADAPTATION TO DIFFERENT TYPES OF GAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 FINAL OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (in cm) 12 - 16 18 - 24 22 - 26 1 Auxiliary 4 Rapid 5 Ultra-rapid In this hob, the supplied reduced grill must only be used for Chinese wok pans. HOB BURNER Ø min. (in cm) 12 - 16 16 - 22 20 - 26 1 Auxiliary 2 Semi rapid 5 Ultra-rapid The following are the diameters of the pans that can be used with the raised pan stand: HOB BURNER 1 Auxiliary 2 Semi rapid 5 Ultra-rapid 10 Ø min. (in cm) 16 - 26 22 - 26 26 - 34 Instructions for the user HOB BURNER Ø min. (in cm) 12 - 20 16 - 24 20 - 26 1 Auxiliary 2 Semi rapid 5 Ultra-rapid The following are the diameters of the pans that can be used with the raised pan stand: HOB BURNER 1 Auxiliary 2 Semi rapid 5 Ultra-rapid Ø min. (in cm) 16 - 26 22 - 26 26 - 34 HOB BURNER Ø min. (in cm) 12 - 16 18 - 26 20 - 31 1 Auxiliary 3 Reduced rapid 6 Dual control HOB BURNER 1 Auxiliary 3 Reduced rapid The following are the diameters of the pans that can be used with the raised pan stand: Ø min. (in cm) 12 - 16 18 - 26 HOB BURNER 3 1 1 Auxiliary 3 Reduced rapid HOB BURNER 1 Auxiliary 3 Reduced rapid Ø min. (in cm) 16 - 24 26 - 28 11 Instructions for the user 5. CLEANING AND MAINTENANCE Before performing any operations requiring access to powered parts, switch off the power supply to the appliance. NEVER USE A STEAM JET FOR CLEANING THE APPLIANCE. 5. 1 Cleaning stainless steel To keep stainless steel in good condition it should be cleaned regularly after use. 5. 1. 1 Ordinary daily cleaning To clean and preserve the stainless steel surfaces, use only specific products that do not contain abrasives or chlorine-based acids. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). 6. 1 Fixing to a support structure model with traditional casing (fig. 1) Create an opening with the dimensions shown in the figure in the top surface of the counter, keeping a minimum distance of 50 mm from the rear edge. Carry out this operation by supporting the hob on the isolating seal and using screws and clamping brackets (Fig. 2 sequence) to fix the hob to the support structure, in order to obtain the complete flatness. The small brackets in figure 2 are only positioned after having mounted the hob. 2) 17 Instructions for the installer CBE54F PSFA906 PGA75F3 - PGA75FSC3 3) PGA95F3 - PGA95FSC3 4) (only "906" models) If laminated surfaces are used, it is advisable to spread a layer of anti-infiltration "primer" across the milled surface. Important: Other types of installation are possible if supervised by the manufacturer! 18 Instructions for the installer Obstructions: location of gas and electric connectors (measured in mm). CBE54F PGA75F3 - PGA75FSC3 PGA95F3 - PGA95FSC3 PSFA906 PGA32 24, 7 Precautions: the temperature of the inside surface of the hob may exceed 125°C. To avoid any hazardous situations, over-the-hob access must be restricted. Refer to the installation instructions. 31, 5 228 122 14, 2 480 19 Instructions for the installer IMPORTANT: if the appliance is mounted on a unit, make sure that a separating shelf is installed, as shown in the figure. However, if the appliance is on an oven installed under the hob, there is no need to install a separating shelf. If installed on top of an oven, the latter must be equipped with a cooling fan. 20 Instructions for the installer 6. 3 Clearances above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances ­ (Measurement A) Range hoods and exhaust fans shall be installed in accordance with the manufacturer's instructions. However, in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood be less than 600 mm or, for an overhead exhaust fan, 750 mm. [. . . ] The regulator supplied must be fitted to the ½ BSP thread at the rear of the appliance. An approved manual shut-off valve must be installed. regulator must be checked and adjusted to 1. 0kPa after installation. Can be connected to the inlet fitting directly. [. . . ]