User manual SMEG CE66MFX

[. . . ] GETTING TO KNOW YOUR COOKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BEFORE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AVAILABLE ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WARNINGS AND GENERAL ADVICE FOR USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 10. 2. 1Using the minute minder The minute minder can be used during cooking or when the oven is turned off. The setting procedure is the same for both cases. Press the button briefly, the symbol will flash and the display will show the time remaining from a previously programmed count). symbol (or the or to increase or decrease the minute minder time from 00:01 to 03:59 (hold Press the buttons the button down to go faster). After a few seconds the count will begin and the remaining time and the steady symbol will appear on the display. and buttons at the same time for approximately one To reset the minute minder, press the second. Warning: The minute minder does not stop the cooking but rather informs the user when the set time has run out. To turn off the oven, turn the PT2 knob to the O position. Modifying the programmed data: Once the count has begun, the previously set data can be modified. Repeat the operations described in point "10. 2. 1 Using the minute minder". 10. 3 Selecting a function A cooking function can be selected by simply turning PT2 to the right or left to the desired function. After having selected the cooking function, use the PT1 knob to select the desired temperature. Cooking is preceded by a preheating stage, which allows the oven to heat to the cooking temperature more quickly. The or waiting for cooking to start, press button the cooking duration can be changed. Press the flash, use the or symbol will begin to buttons to modify the end of cooking time. symbol will stop flashing, and automatic cooking will restart A few seconds after the last change, the with the new programmed data. Once cooking has been programmed, but before it starts, the symbol of the chosen function or recipe will remain on, as will the , symbols. 10. 5 Cooking with selection of a recipe The oven has 8 preset recipes (see "10. 6 Table of predefined recipes:") and 2 memories. A recipe is a combination of function, temperatures and cooking times presettings. Only when PT1 is positioned on "O" it is possible to select a recipe simply by turning PT2 onto . Press the or keys; the selected recipe will change its colour to red on the display; a few seconds later cooking will start with the preset parameters. When the preset temperature is reached, a series of beeps will be emitted indicating that the oven is ready for use. The cooking time as specified in the table "10. 6 Table of predefined recipes:" starts from this moment. Modifying the data set (during cooking) During cooking it is possible to manually change the temperature that was preset for the recipe by turning PT1 to the desired cooking temperature. To modify the cooking time press the key; the or symbol flashes on the display. You can increase or decrease the cooking end time using the keys. [. . . ] To reassemble, fit the hinges A into their grooves, then lower the door into place and release the levers B. 15. 3 Removing the door seal To permit thorough cleaning of the oven, the seal may be removed. Before removing the seal, take off the door as described above. Once the door has been taken off, lift the tabs at the corners as shown in the figure. 51 Instructions for the User 15. 4 what to do if. . . The oven display is completely off: · · · Check the mains power supply. Check whether an omnipolar switch upstream from the oven feed line is in the "ON" position. [. . . ]