User manual SMEG CF36XPNF

[. . . ] Never touch the machine with your wet, damped hand or foot. Never open the detergent compartment when the appliance is running. Never force the door to open when the washing machine is running. Do not touch discharging hose and water during discharging as the appliance may reach high temperatures when running. [. . . ] Your machine will finish the programme after wringing your laundries in the wringing revolution you have selected. 24 CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 2-Washing water temperature selection You can select the washing water temperature with the washing water temperature adjustment button. Whenever you select a new programme, the maximum washing water temperature is shown on the washing water temperature display. You can gradually decrease the washing water temperature between the maximum temperature and cold washing (--) by pressing washing water temperature adjustment button. If you have missed the washing water temperature you wanted, you can return to the intended temperature by continuously pressing the washing water temperature adjustment button. 25 CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 3-Auxiliary function prewash You can expose your very dirty laundries to prewashing operation prior to main washing by using this auxiliary function. When using this function, you should put detergent in front washing compartment of the detergent drawer. 4-Auxiliary function for rapid wash This auxiliary function will enable the washing duration of your laundries that are not very dirty to be shortened. In case you put half of or less than half of the laundry capacity of the washing programme you have selected in your machine, your machine will detect this event thanks to automatic Half-load detection system, and the programme you have selected will wash your laundries in a shorter time to consume less energy and water. If your machine detects half load, symbol will automatically flash on electronic display. To cancel it, pressing on the auxiliary function of quick washing for once will be enough. However, selection of auxiliary function of quick washing is not possible in course of the same washing operation. 5-Auxiliary function for easy ironing You can enable your laundries to be taken out less wrinkled as the washing operation is completed by employing this auxiliary function. 26 CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 6-Auxiliary function for delay timer By using this auxiliary function, you can let your machine start washing after half an hour to 23 hours. To use auxiliary function of delay timer: - Press time delay button once. - Expression of “0. 5h” will appear on the display. - Press on time delay button until the time, on which you want washing operation to be started. - To activate the time delay you have selected in the programme, you may press on any auxiliary function button you like except “Start/Pause” button. - You can run your machine by selecting a new programme. 32 CHAPTER 6: OPERATING YOUR MACHINE FINISHING PROGRAMME Finishing programme - Your machine will stop by itself as soon as the programme you have selected finishes. -Expression of “END” will flash on the electronic display. Note: Within 2 minutes after the programme has finished, your machine will extinguish the electronic display to save energy. It will reflash when pressed on a button of any auxiliary function. - If you see that the symbol indicating that the door can be opened flashes on the electronic display, you can open the door of your machine and remove the laundries. - Leave the door of your machine open to allow the inner part of your machine to dry after removing your laundries. - Turn the water faucet off. 33 CHAPTER -7: ELECTRONIC DISPLAY WARNING SYMBOLS WARNING OF WATER CUT-OFF / LOW MAINS WATER PRESSURE If symbol flashes on the electronic display: - Water faucet may be closed. If so, switch the programme knob to position 0. You can select a programme and run your machine after the mains water is supplied. (*) - Valve inlet filter may be clogged. (*) (*) See the chapter regarding maintenance and cleaning of your machine. 34 CHAPTER -7: ELECTRONIC DISPLAY WARNING SYMBOLS WARNING OF CLOGGED PUMP FILTER If symbol flashes on the electronic display: - Pump filter may be clogged. (*) - Discharging hose may be clogged or twisted. Check the discharging hose. (*) See the chapter regarding maintenance and cleaning of your machine. 35 CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR MACHINE Unplug your machine. [. . . ] Water in the non-visible part of the drum. Non-dissolving particles of some detergents may adhere to your laundries as white spots. Perform an extra rinsing by setting your machine to “Rinsing” Laundries have programme, or clean detergent residues on the spots using a them. Apply the maximum amount of detergent The reason for this instructed by the Grey spots appear on spots may be oil, detergent the laundries. manufacturer in the next washing operation. [. . . ]