User manual SMEG CLE300LF

[. . . ] The user is thus obliged to consign scrapped appliances to the special electronic and electrotechnical waste disposal centres, or return them to the dealer on purchase of a similar new appliance, on a one-to-one basis. Consignment to the appropriate facility for environmentally responsible recycling, treatment and disposal helps to prevent any negative effects on the environment and health, and encourages the reuse and/or recycling of the appliance's component materials. Illegal dumping of the appliance by the user will be subject to prosecution under the relevant law. 1 EN READ THE INSTRUCTIONS Attention!You are advised to read all the instructions in this manual carefully; it will inform you about the right conditions for the proper, safe use of your washer-dryer It is very important to keep this instruction manual with the appliance for future reference. [. . . ] This will provide the desired effect with optimal detergent consumption. On detergent packs the recommended dose is indicated for 4 levels of water hardness and for loads of 4-5 kg of laundry with average dirt levels. Request information about the water's hardness from your water supply company. Water hardness Level of hardness Soft Medium Hard Very hard French degrees fH Up to 15° 15° - 25° 25° - 40° More than 40° German degrees dH Up to 8° 8° - 14° 14° - 22° More than 22° 10 EN 4. 6 POWDER DETERGENT DOSES Laundry with normal dirt 1. Pour the total amount of detergent shown on the pack into the main wash compartment of the detergent drawer. Place ¼ of the recommended amount of detergent in the prewash compartment of the detergent drawer and ¾ of the detergent in the wash compartment. · If no recommended doses are provided, for delicate items in synthetic fibre use from ½ to 2/3 of the recommended dose for washing tough cotton fabrics. · Only neutral detergents recommended for wool should be used on the wool programme. · Use the doses recommended by the detergent producer. 4. 7 LIQUID DETERGENT DOSES 1. Pour the dose required into the measuring cap supplied with the bottle of liquid detergent and place it in the drum, or use the main wash compartment of the detergent drawer, fitting the insert provided. The scale on the red insert is intended as an aid when deciding the dose of liquid detergent. Warning!The appliance comes with the buzzer function "on". To confirm the selected option, simply press the Confirm options button and the LED of the option remains on. To delete an option selection, simply return to the option with the Selection button and press the Confirm options button. To annul all the options previously selected in a single operation, simply hold down the Confirm options button for 4 seconds. The Buzzer option retains its "on" or "off" status for subsequent cycles. It is only automatically switched to "off" if the Night Wash programme is chosen. 13 EN 4. 12 TIME TO END Time to end symbol Start pause symbol Start Pause Time to end button 1. The Time to End key can be pressed repeatedly to select the time after which the washing programme will end. The time to end of cycle function calculates the initial duration of the washing/drying cycle, the settings made (temperature, spin speed and options) which may shorten or lengthen the cycle's initial duration, and the delay time the user wishes to add before the cycle starts. After the time to end has been set, the symbol on the display remains on. To annul the Time to End function, keep pressing the key repeatedly until the display shows 0. The Start Pause symbol flashes on and off until the cycle starts. [. . . ] Using the template 1) Measure the height of the kitchen baseboard: the height of the wooden panel is obtained by first establishing the height of the kitchen baseboard. E. g. : for a 100 mm high baseboard, the maximum height of the panel is 720 mm. If the height of the baseboard must be increased, the height of the wooden panel must be reduced. Applying the panel 4 Place the template of the inner side of the panel and match the height of the baseboard with the lower edge of the panel (fig. Make sure the template is horizontally centred with reference to the vertical lines marked at the ends. [. . . ]