User manual SMEG CS19NLSE

[. . . ] This user-friendly manual will provide answers to all your questions about use of the dishwasher. For any other information about use and maintenance of the dishwasher, read the enclosed manual carefully. USER INSTRUCTIONS: useful information is provided for the use of the washing programs and all the dishwasher's functions. User instructions 1. Description of the controls 1. 1 Front panel All the dishwasher control are grouped on the front panel. Programming and option selection are only possible with the door closed. 1 2 3 4 5 6 7 8 9 ON/OFF BUTTON START/PAUSE BUTTON SELECTION PROGRAMS BUTTON PROGRAMS LIGHTS LOAD WASH BUTTON (on some models only) LOAD WASH LIGHT (on some models only) NO SALT LIGHT NO RINSE AID LIGHT RECESSED DOOR HANDLE User instructions SETTING THE WASHING PROGRAM To select the most suitable program for the dishes to be washed refer to the table below, which indicates the most appropriate program according to dish type and degree of soiling. PROGRAM SELECTION TYPE AND GRADE DIRT PROGRESS PROGRAM DURATION MINUTES (2) CONSUMPTION WATER LITRES (1) POWER KWh (2) SOAK PANS AND DISHES IN WAITING OF COMPLETING THE LOAD Cold prewash 15' 6 0, 03 LIGHT DISHES NOT VERY DIRTY Wash at 45C Cold rinse Rinse at 68C Dry Cold prewash Wash at 50C Cold rinse Rinse at 65C Dry Cold prewash Wash at 65C Cold rinse Rinse at 68C Dry Prewash at 45C Wash at 70C 2 cold rinses Rinse at 70C Dry 70' 15 1, 15 BIO (*) PANS AND DISHES NOT VERY DIRTY BUT WITH DRY RESIDUALS 160' 17 1, 05 NORMAL PANS AND DISHES DIRTY AND WITH DRY RESIDUALS 100' 20 1, 40 SUPER PANS AND DISHES VERY DIRTY AND WITH DRY RESIDUALS 115' 24 1, 77 Only run the soak program with half loads. [. . . ] The covering fixtures are available as an accessory from specialist dealers or the After-Sales Service. - To build in the dishwasher, the special kit must be purchased from authorised dealers or the After-Sales Service. Some models are equipped with only one adjustable foot at the rear, which can be adjusted by turning the screw on the lower front part of the appliance. Installation instructions 2. 1 Water supply connection Preventing the risk of clogging or damage: if the water pipe is new or has not been used for a long time, before connecting to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance. The dishwasher must always be connected to the water system with new hoses; old or used hoses must never be reused. CONNECTING TO THE WATER SUPPLY Connect the intake hose to a cold water supply with " gas thread, inserting the filter A supplied with the dishwasher. Take care to screw the hose firmly into place with your hands and then complete by tightening about of a turn with pliers. In dishwashers equipped with the ACQUASTOP device, the filters is already fitted inside the threaded ring. The dishwasher can also be connected to a hot water supply not exceeding 60C. Supplying the appliance with hot water cuts down the washing time by approximately 20 minutes, but slightly reduces its effectiveness. Make the connection to the domestic hot water supply using the same procedure described for connecting to the cold water supply. DRAIN CONNECTION Insert the dishwasher's drain hose into a drain pipe having a diameter of at least 4 cm, or alternatively, place it inside the kitchen sink using the plastic support provided, taking care not to crush or excessively bend the hose. The container is situated at the bottom of the dishwasher. After removing the lower basket, unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher. Before replacing the cap, remove any salt residues from around the opening. When using the dishwasher for the first time, in addition to the salt it is also necessary to add one litre of water to the container. Each time the salt container is refilled, make sure that the cap is securely closed. The mixture of water and detergent must never penetrate the salt container, as this would compromise the operation of the regeneration system. In the event of this occurring, the warranty will be invalidated. Only use regenerating salt specially formulated for domestic dishwashers. If using salt tablets, do not fill the container completely. User instructions Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system. When necessary, refill the regenerating salt container before starting the washing program. In this way, the excess saline solution will be immediately removed by the water; the prolonged presence of salt water inside the tank may lead to corrosion. Be careful not to confuse the salt and detergent packages; adding detergent to the salt container will damage the water softening system. 3. 2 Using the rinse aid and detergent dispensers The detergent and rinse aid dispensers are situated on the inner part of the door: the detergent dispenser is on the left, and the rinse aid dispenser is on the right. With the exception of the SOAK program, before every washing cycle it is necessary to add the required amount of detergent to the detergent dispenser. [. . . ] After reassembly, check that the spray arms turn freely. Otherwise, check that they have been installed correctly. User instructions CLEANING THE FILTER UNIT It is advisable to periodically inspect the centre filter C and, if necessary, to clean it. To remove the filter, grip the tabs, turn them anticlockwise and lift upwards; push the centre filter D from the underside to remove it from the micro-filter: separate the two parts which make up the plastic filter by pressing the body of the filter in the zone shown by the arrows; remove the centre filter by lifting it upwards. GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE: The filters should be cleaned under running water using a stiff brush. It is essential to thoroughly clean the filters according to the above instructions: the dishwasher cannot function if the filters are clogged. [. . . ]