User manual SMEG CS20NL-6

[. . . ] BEFORE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DESCRIPTION OF FRONT PANEL CONTROLS . . . . . . . . . . . . . USING THE OVEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USING THE PIZZA FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To prevent excessive amounts of condensation from forming on the internal glass, food should not be left inside the oven for too long after cooking. 7. 2 Cooling fan system The appliance is equipped with a cooling system which comes into operation as soon as a cooking function starts. Operation of the fan generates a normal air flow which comes out above the door and may continue for a short time even after the oven is turned off. 7. 3 Inside lights (Toast) The oven lights come on when any function is set except for the function. 41 Instructions for the User 8. USING THE PIZZA FUNCTION This appliance is equipped with a function specially developed for cooking pizza with the special plate provided. This function is identified by the symbol on the oven functions knob. To cook a pizza, proceed as described below. Set the oven functions knob on the symbol and the thermostat knob on the symbol. Preheat with these settings until the thermostat light goes out, then place the pizza on the special plate using the pizza shovel provided. It does not normally take more than 3-4 minutes to cook a pizza to perfection, although this time may vary depending on the dough used or individual taste. 8. 1 · Precautions for using the pizza plate Never use the pizza plate except as described above (for example, never use it on gas or ceramic hobs, or on ovens not designed to take this accessory). · For conventional cooking operations, it is advisable to remove the pizza plate and replace it with the bottom cover provided. · If you like oil on your pizza, it is best to add it after removal from the oven since oil stains on the pizza plate are unsightly and may reduce its efficiency. Never use any oven function if the pizza plate or cover is not in position. 8. 2 To save energy The pizza stone acts as a heat reservoir. It can be stopped in manual mode by pressing the and keys together. To switch off the appliance, return all the knobs to the 0 setting in sequence. 10. 8 Deleting the data set With the program set, keep the key of the function for deletion ( or ) pressed, while at the same time setting the value by pressing the value modification keys or . The programmer will interpret deletion of the duration as the end of cooking. 10. 9 Modifying the data set The cooking data set can be modified at any moment by keeping the key of the function for modification ( or ) pressed and at the same time pressing the value modification keys or . 47 Instructions for the User 11. ACCESSORIES AVAILABLE The oven is fitted with 4 runners for placing trays and shelves at different heights. Roof liner: remove it to simplify cleaning inside the oven. Shelf: useful to support pans containing the food for cooking. Tray grid: for placing on top of a tray for cooking foods which may drip. Oven tray: useful for collecting fat from foods placed on the grid above. Tongs: The tongs can be used either for removing hot trays or for taking out the pizza plate as described in paragraph 13. 6 Cleaning the pizza plate. Rotisserie frame: supports the rotisserie rod (see page 52 for instructions for use). Rotisserie rod: useful for cooking chicken and all foods which require uniform cooking over their entire surface. Pizza plate: specially designed for cooking pizza and related foods. USING THE PIZZA FUNCTION" 48 Instructions for the User Pizza shovel: a convenient way of putting the pizza on the special plate in the oven. Toasting racks: the appliance comes complete with two toast racks. The racks must be placed inside the slots in the toaster. [. . . ] Before carrying out any operation involving access to live parts, disconnect the appliance from the electricity supply. 14. 1 Changing the light bulbs Remove the protective cover A by unscrewing it anti-clockwise and replace the bulb B with another of the same type (25 W). Replace the protective cover A. Use only light bulbs approved for ovens (T 300°C). 58 Instructions for the User 14. 2 Removing the door 14. 2. 1 With type 1 mobile levers With the door completely open, lift the levers A of the two hinges until they touch the hinges B and take hold of the two sides of the door with both hands close to the 1) hinges themselves. Raise the door to an angle of about 45° and remove it. If the hinges have not locked, repeat the operation, raising the levers A and keeping the door slightly raised. [. . . ]