User manual SMEG CSU2007W1

[. . . ] This product complies with current European safety standards governing electrical appliances. It has been subjected to thorough and meticulous testing to assess its safety and reliability. Before using the appliance, read this manual carefully as it will tell you what to do and what not to do. Improper use of the appliance can be dangerous, above all for children. 907 GB Before connecting the appliance, make sure that the data on the rating plate complies with that of the domestic supply. [. . . ] These plastic elements prevent the shelves from moving during transport. To remove the shelf locking devices, proceed as follows: a) Grasp the plastic locking device and rotate it until it comes away from the shelf. b) Remove the locking device by pulling it outwards. GB 907 2a D P 2b 2 B 2d H 2c 2f GB 1 POSITIONING AND INSTALLING THE APPLIANCE 2d Remove the upper hinge pin K and fit it to the opposite side. 2f Refit the upper door. 7 Once the appliance has been unpacked, check that the mains voltage is the same as that indicated on the rating plate. If the door opening direction is as required, go to Point 3. Otherwise, reverse the position of the hinges. To do this, carefully place the appliance on its back. Use spacers to prevent crushing the condenser pipes and damaging the compressor unit. 2 2a Remove the lower hinge pin P and the distance spacer D. 2c Slide off hinge cover H; remove the middle hinge C, then free the upper door. 907 2g L C 2h 2i 2l P D 2m 8 POSITIONING AND INSTALLING THE APPLIANCE 2g Fit hinge C and support L on the left side. (The hinge cover H, must be refitted at the end of installation). 2h Refit the middle support L on the right side. If the freezer compartment is warm, the red led (S6) (alarm) starts to flash, and turns off automatically when the freezer compartment reaches the temperature of -12°C . 13 CONNECTING THE APPLIANCE TO THE MAINS SUPPLY Check that the mains voltage corresponds to that indicated on the appliance's rating plate and that the mains socket is equipped with an earth connection. If the appliance is switched off then immediately back on again, the compressor will start to operate after approximately 10 minutes. START-UP AND CONTROL OF REFRIGERATOR COMPARTMENT On insertion of the plug in the mains socket, if the green led (S2) (minimum position) does not light, this means that the appliance is switched off. To start up the appliance, press button T1 for at least 0. 5 seconds. To interrupt operation, press T1 for at least 4 seconds. On power-up, operation is indicated by illumination of 907 S5 S3 T1 S6 S4 S2 14 USING THE FRIDGE COMPARTMENT - Temperature programming and control: 3 different temperatures can be selected, as indicated by the 3 green leds (S2-S3-S4). To change settings, press button (T1); on each click the illuminated led turns off and the next one flashes for 4 seconds according to the sequence S2-S3-S4 - S5. The new setting is saved at the end of the flashing phase. Activation of SUPER mode (S5) is by means of button (T1) after which the yellow led (S5) is permanently lit. The programmed functions are memorised also in the event of a power failure or when the appliance is disconnected. · Keep all liquids in closed containers. GB The NO-FROST system guarantees a constant temperature and a more rapid freezing capacity. [. . . ] The protections (wire grill, covers) must not be removed by unqualified personnel: do not use the appliance if the protections have been removed. GB - Disconnect the appliance from the mains electricity supply. - Clean both the compartments and dry them. - Leave the doors open to prevent bad smells or mould from forming. When cleaning the internal plastic parts and the door gasket: do not use abrasives or detergents of any kind. - Use a warm solution of bicarbonate of soda (two spoonfuls in two litres of water). 1 Cleaning the condenser - This should be carried out at least twice a year. [. . . ]