User manual SMEG CW500RU

[. . . ] PROFESSIONAL DISHWASHER 1 Precautions for safety and use 2 Technical data 3 Installation and positioning 4 INSTALLATION INSTRUCTIONS FOR THE AFTER-SALES SERVICE 5 Start-up 6 Settings 7 Malfunctions shown on the display (for the technician) 8 INSTRUCTIONS FOR THE USER 9 Choosing the program 10 Supplementary Functions 11 Maintenance and cleaning 12 Troubleshooting 13 Malfunctions shown on the display (for the user) You are advised to read all the instructions in this manual carefully to become familiar with the right conditions for the proper use of your dishwasher. TECHNICAL INSTRUCTIONS: These are intended for the qualified staff who are to install, commission and test the appliance and carry out any servicing and repairs. INSTRUCTIONS FOR THE USER: These provide recommendations for use, a description of the controls and the correct procedures for cleaning and maintaining the dishwasher. 1 Precautions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE DISHWASHER AND MUST ALWAYS BE KEPT WITH THE APPLIANCE. POSITIONING, CONNECTIONS, COMMISSIONING, TROUBLESHOOTING AND REPLACEMENT OF THE POWER SUPPLY CABLE MUST BE CARRIED OUT BY SKILLED STAFF. THE DISHWASHER IS INTENDED ONLY FOR PROFESSIONAL USE BY TRAINED STAFF. IT IS DESIGNED TO WASH TABLEWARE (PLATES, CUPS, BOWLS, OVEN DISHES AND CUTLERY) AND SIMILAR ITEMS IN THE RESTAURANT AND INSTITUTIONAL CATERING SECTOR, AND COMPLIES WITH THE INTERNATIONAL STANDARDS ON ELECTRICAL AND MECHANICAL SAFETY (CEI-EN-IEC 60335-258/61770) AND ELECTROMAGNETIC COMPATIBILITY (CEI-IEC-EN 55014-1/-2, 61000-3;4, 50366). [. . . ] Generally H03 will be satisfactory for most users. At first use, the salt tank has to be filled. It is subsequently sufficient simply to fill up with regenerating salt when necessary. Hardness Hardness Setting level (°dH german (°dF French Modify the value degrees) degrees) of the parameter Regeneration off Regeneration off H00 by pressing . 8, 5 15 H01 11 20 H02 17 30 H03 22, 5 40 H04 28 50 H05 Regeneration cycle duration: 12 minutes 33, 5 60 H06 · · With values over 60°dF an external water treatment device must be used and the regeneration frequency must be set on H00. · 10 6. 1. 7 tStP (minimum rinsing temperature) function Modify the parameter (ON/OFF) by pressing . Set at "on" for minimum rinsing temperature as set. Set as "off" to accept minimum rinsing temperature a few degrees lower than the setting if hot intake water is not used. 6. 1. 8 Rinse aid pump To reset, press for 3 seconds. Display (also reset when needed) 6. 1. 9 Detergent pump To reset, press for 3 seconds. Display (also reset when needed) 6. 1. 10 Energy consumption ­ Display and reset To reset, press for 3 seconds. 6. 1. 11 Customisation of duration of program P4 The duration of program P4 can be customised from 5 to 20 minutes using the appliance parameter modification procedure, but the dishwasher must be set on program P4. After setting program P4 access the programming procedure and scroll through to "inF" (last parameter to appear) then press the button to modify the duration of the cycle (from 5 to 20 minutes) After a few seconds without the user pressing any buttons, the display will return to the normal operating status and the modifications will be saved. 11 6. 1. 12 Setting the Model (for After-Sales Service only) Modify by pressing . 6. 2 Starting the peristaltic pumps ­ rapid filling of detergent and rinse aid delivery circuit. Perform after the parameter modification procedure explained in the previous point. Indicator lights as follows: off; green; orange; flashing. With the dishwasher powered up, access "programming mode" by pressing the on/off button for a few seconds; at the "beep", release the button and press it again quickly within 0. 5 seconds. The peristaltic pumps continue to operate until the same buttons are pressed again. The rinse aid and detergent symbol lights remain on as long as work is in progress; bear in mind that the rinse aid peristaltic pump fills the circuit in about 7 minutes, while for the detergent it only takes 2 minutes. 12 7 MALFUNCTIONS SHOWN ON THE DISPLAY The dishwasher is able to identify a number of malfunctions and show them on the display. If the problem persists after the dishwasher has been switched off and back on, proceed as described below: Err01 Err04 The anti-flooding system has been activated (for the relevant models only). Tank temperature probe malfunction Large water leak : check the origin of the problem. Tank temperature probe disconnected or not working Check dynamic pressure in intake system, inspect water intake filter and clean if necessary. Err05 Tank water filling malfunction If the problem persists: - tank pressure switch has failed (continuous empty reading) - leak from pipe connected to air trap - valve vent exhaust pipe blocked Inspect the filters for dirt and that the drain hose is not blocked, bent or crushed. Check that the drain pump is not blocked by dirt by removing the insert on the sump (from inside the tank) If the problem persists: with the tank empty: tank pressure switch defect (the contact is locked on full) with tank full: drain pump has failed - with tank full: see above (water pump-out malfunction) - with tank empty: safety pressure defect (the contact is locked on full) -circuit board relay failure, - contactor failure. - boiler safety thermostat failure, - boiler temperature probe faulty or incorrectly positioned - water continues to enter the tank due to tank pressure switch defect boiler temperature probe disconnected or not working Check that the water intake tap is on and the dynamic pressure in the intake system, inspect the water intake filter and clean if necessary. Err06 Water pump-out malfunction Err09 Tank water level too high Err23 Boiler heating malfunction (does not heat up) Err24 Boiler temperature probe malfunction Err25 Boiler water filling malfunction If the problem persists: - boiler pressure switch has failed (continuous empty reading) - pipe leaking/disconnected - check that rinsing spray arm nozzles are clean - boiler pressure switch has failed (continuous full reading) - rinsing pump not working Boiler pressure switch has failed (continuous full reading) -circuit board relay failure, or - contactor failure Err26 Err27 Err28 Boiler emptying malfunction Boiler emptying malfunction ­ with tank full Boiler heating malfunction (overheating) 13 8 INSTRUCTIONS FOR THE USER 8. 1 Control panel On-off button Program selection button Start CONFIRM/PAUSE button Total emptying button (tank and boiler) Additional function selection button L1 Main power on light L2 Intake/standby cycle in progress light (orange/green) L3 Pump-out in progress light No rinse-aid symbol (if a system for monitoring outside the dishwasher is provided) Tank heating element on symbol No salt symbol (if softener is fitted) Boiler element on symbol No detergent symbol (if a system for monitoring outside the dishwasher is provided) 14 8. 2 Before washing Use only detergents and rinse aids for industrial dishwashers. Do not use detergents intended for hand washing. We recommend the use of Smeg products, specially developed for this dishwasher. When topping up the tanks, take care not to swap the products; this might damage the dishwasher and cause malfunctions. Do not mix different detergents; this would damage the dispenser device. Industrial dishwasher detergents may cause serious irritations. [. . . ] Finally, turn off the master switch, close the water intake valve and leave the door ajar until the interior is completely dry. The detergent and rinse aid intake hoses must be put back into the containers when the dishwasher is returned to service, taking care not to swap them over (red hose = detergent, blue hose = rinse aid). 20 12 TROUBLESHOOTING If the system fails to pump out because the drain pump is fouled (as a result of incorrect filter positioning), proceed as follows: Bale out the dishwasher with a basin and disconnect it from the electrical mains. Unscrew the screw A, release the tang B and lift it. Check that the impeller of the drain pump underneath the cover turns freely, and is free from dirt, limescale residues, or pieces of glass. [. . . ]