User manual SMEG CWC500R

[. . . ] THE SYMBOL ON THE PRODUCT, OR UPON ITS ACCOMPANYING DOCUMENTATION, INDICATES THAT THIS PRODUCT MUST NOT BE TREATED AS DOMESTIC WASTE, BUT MUST BE TAKEN TO A SUITABLE COLLECTION DEPOT FOR THE RECYCLING OF ELECTRIC AND ELECTRONIC APPARATUS. DISPOSE OF THE APPARATUS ACCORDING TO THE LOCAL WASTE DISPOSAL NORMS. FOR MORE INFORMATION ON THE TREATMENT, RECOVERY AND RECYCLING OF THIS PRODUCT, CONTACT YOUR COMPETENT LOCAL AUTHORITY, YOUR DOMESTIC WASTE DISPOSAL SERVICE OR THE STORE IN WHICH THE PRODUCT WAS PURCHASED. DO NOT INSERT SOLVENTS SUCH AS ALCOHOL OR TURPENTINE WHICH COULD PROVOKE EXPLOSIONS. [. . . ] Connect the apparatus to the usage equalizer. The clamp for the connection is located at the lower back of the machine. The protection conductor (PE) is yellow-green in color, the neutral conductor (N) is blue and the phase conductors (L1, L2, L3) are black, gray and brown. 5 FIRST STARTUP FIRST STARTUP The electrical protection system must be subjected to a functional test before use. The installation must be performed and/or verified by the authorized reseller who will be responsible for the first startup and the instructions relative to the dishwasher's operation. PREPARATION FOR USE Important: The rinse-aid metering unit comes equipped in all models while the detergent metering unit comes equipped in only some models. If both metering units are present position the external detergent and rinse-aid containers and insert their respective suction tubes located at the back of the machine. Red tube: detergent Transparent tube: rinse-aid Before inserting the tubes in the containers apply the weight (necessary to keep the tube at the bottom of the container) and the filter as indicated in the diagram. For adjustments, use the adjustment screws indicated in the diagram. It is recommended that adjustments be performed by personnel from the companies who have supplied the detergent products. If the detergent metering unit did not come pre-installed it can be installed at a later time by ordering the relative KIT. Alternatively, an external metering unit can be connected by means of an electrical connection with a 2x0. 5 mm type H05 RN-F cable. This cable must be inserted through the passage indicated in the TECHNICAL CHARACTERISTICS scheme and connected in accordance with the electrical scheme furnished with the dishwasher. The metering unit must be of 230V/50Hz with a maximum absorbed power of 15W. Connect the detergent metering unit to the dishwasher through the red tube cited above. Do not use detergents intended for hand washing. It is recommended to use products which were designed especially for this dishwasher. During the loading of the tanks be careful not to switch products as this could provoke dishwasher malfunction and damage. Do not mix different detergents together as this could damage the metering unit. Detergents for industrial dishwashers can cause serious irritations. Take care to respect the instructions provided by the detergent manufacturer on the packaging. 9 Open the water supply faucet (usage). Verify: The levels of detergent and rinse-aid in the containers. The correct positioning of the filters, the rotation of the sprinklers, the absence of foreign objects within the dishwasher. Turn off the main switch (usage), "OFF" appears on the display. 8. 3 FIRST DAILY USE (Tank and boiler empty) Activate the wall switch. Two small illuminated points on the display will turn on; the led indicator on the left of the switch will be lit red in order to indicate that the machine is receiving electrical current; Position the overflow and close the hood. The led indicator to the right of the button turns green and the led indicator will begin to flash. Once filling has been completed it machine begins to fill itself. [. . . ] Wait for the turn on led indicator to THE WASH PROGRAM DOES NOT START The dishwasher has not finished loading Sprinkler wash holes are clogged or encrusted Detergent or rinse-aid insufficient or not adequate Disassemble and clean the sprinklers (10. 2 Periodic checks) Verify detergent type and quantity. Verify the temperature shown on the display, if below 50°C call Assistance. Increase the duration of the wash cycle, particularly if dishes are very dirty or contain partially dried residues. POOR WASHING RESULTS Plates / glasses poorly positioned Low wash temperature Inadequate cycle setting Sprinkler nozzles clogged Calcium encrustations in boiler RINSE INSUFFICIENT the Verify the cleanliness of the nozzles and the correct function of any installed water softeners. Verify the rinse-aid container and ensure its adequacy for use with the water supply. [. . . ]