User manual SMEG CX61VMLS5

[. . . ] 9 4. 1 Examples of outdoor situations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5. GETTING TO KNOW YOUR APPLIANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BEFORE INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Unscrew the cap A and remove the seal B; · replace the battery C with another of the same type; · take care that the battery poles correspond (see diagram on the right); · replace the seal B and screw the cap A back on. Warning Flat batteries must not be dumped at random or disposed of with other waste. They must be collected separately and consigned to your local waste disposal company, or disposed of in the special containers provided for old batteries. 12 Instructions for the installer 7. 4 Connecting the gas cylinder to the appliance All the adjustments necessary to allow the appliance to function correctly are made in the factory. The only procedure required for correct operation is connection of the hose supplied with the appliance, as described below Connection of the appliance to the gas supply must be in accordance with the requirements of AS5601/ AG601. This product is set in the factory to use LPG gas sold in suitable cylinders obtainable from specialist outlets. The appliance comes complete with a rubber hose with pressure regulator and unions. The pressure regulator is preset in the factory to ensure the appliance functions to the highest standards. The diagram below shows how to connect the hose supplied to the product and the gas cylinder. Australia fitting New Zealand fitting The product leaves the factory set to operate on LPG. If it should become necessary to change the type of gas and thus the nozzle diameter, contact your nearest authorised service centre. If the appliance does not function to your satisfaction, DO NOT ATTEMPT TO REPAIR IT YOURSELF; contact your nearest authorised service centre. The table below provides the key to the symbols used. LEFT BURNER IGNITION KNOB BURNER IGNITION BUTTON (ON SOME MODELS ONLY) DRIPPING PAN "SMOKER" TRAY (ON SOME MODELS ONLY) RIGHT BURNER IGNITION KNOB CENTRAL BURNER IGNITION KNOB (WITH IGNITION PLUG ON ALL MODELS WHERE FITTED) BURNER IGNITION BUTTON (ON RELEVANT MODELS ONLY) On models fitted with this button, to light the flame, turn the burner ignition knob anti-clockwise to the minimum flame symbol while pressing it down. To adjust the flame, turn ) and the the knob to the zone between the maximum ( minimum ( ) settings. To turn off the burner, turn the knob back to the OFF position. BURNER CONTROL KNOB On models without burner ignition button, to light the flame proceed as described in point "9. 2. 1 Lighting the burners by hand (on all models)", pressing down the knob and turning it anti-clockwise to the minimum flame setting adjust the flame, turn the knob to the zone between the maximum ( the minimum ( position. To turn off the burner, turn the knob back to the OFF 17 Instructions for the User 9. USING THE BARBECUE This appliance is not fitted with a safety valve. It therefore must never be left unattended when in operation. If you notice that the flames have gone out, turn the knobs to the OFF position AT ONCE and wait a few minutes before attempting to ignite the burners again. The lid, provided on some models only, must always be kept open while the burners are being lit. It can be lowered once they have ignited and must be raised as soon as the thermometer fitted on it reaches 300°C. Take care not to obstruct the combustion gas outlet flue in the back of the lid (if any). [. . . ] 11. 1. 1 Routine cleaning When cleaning and caring for stainless steel surfaces, always use only specific products which do not contain abrasives or chlorine-based acids. Instructions for use: pour the product onto a damp cloth and wipe over the surface, then rinse thoroughly and dry with a soft cloth, chamois leather or paper kitchen towel. For the best results, we recommend using an abrasive, non-scratch pad. 11. 1. 2 Food stains or spills Never use metal scouring pads or sharp scrapers; they will damage the appliances external surfaces. [. . . ]