User manual SMEG CX61VMN

[. . . ] 31 4. 1 Examples of outdoor use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5. GETTING TO KNOW YOUR APPLIANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BEFORE INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Once the barbecue hose has been connected to the gas supply (LPG or Natural Gas), proceed as follows: 1) Open the gas valve on the LPG cylinder (or turn on the tap for Natural Gas), BUT DO NOT ATTEMPT TO LIGHT THE BURNERS. 2) While there is gas pressure in the hose, check all the connections for leaks using a soap and water solution. Never look for leaks with a naked light. 3) 4) 5) If there are any leaks, bubbles will appear on the poor connection from which gas is escaping. Turn off the cylinder gas tap, tighten the connection which was leaking and repeat the test. If the gas leaks persist, contact your nearest supplier. NEVER CHECK FOR LEAKS WITH A NAKED LIGHT. 36 Instructions for the Installer 7. 6 Fixing the gas cylinder to the trolley (optional) To secure the gas cylinder to the trolley, use the chain provided, passing it through the points shown in the diagram. Fit one link of the chain over the pin A, then pass it over points B and C on the top of the cylinder, through the hole D and underneath the frame. Then bring the chain out of the frame in point E, fix it to the pin A again and tighten the ring-nut. If the pin which secures the chain has to be replaced, refer to the illustrations below which show how to fit and fix the pin. 1) 2) 7. 7 Hose clip There is a hose clip on the trolley. It must be used to prevent the hose from touching other surfaces in the section between the appliance's gas connection and the cylinder connection. The bottom of the carriage is able to take gas cylinders up to 50 cm tall (with pressure regulator fitted). The pressure regulator outlet should be horizontal. 37 Instructions for the User 8. THE CONTROL PANEL All the appliance's control and monitoring devices are placed together on the front panel. To fit it, simply screw the two screws (supplied) into the holes provided on the right hand side of the barbecue. Align the holes in the barbecue (A) with the holes in the rotisserie motor (B). Then screw in the two screws to join the two parts together. To use the rotisserie motor simply connect the plug to the electrical mains and set the switch on I to turn it on. To switch it off, simply return the switch to 0. CAUTION: do not expose the rotisserie motor to bad weather as this might damage the device and reduce its safety level. If necessary, remove the device from the barbecue by unscrewing its fixing screws and store it in a place protected from the weather. CAUTION, in case of damage to the rotisserie motor power supply cable, do not attempt to repair or replace it yourself; contact an authorised service centre immediately. Warning: disconnect the plug from the electrical mains before cleaning the rotisserie motor. Do not place the rotisserie in water to clean it. 40 Instructions for the User 9. 3 Grid and plate positions Before starting to cook, always check that the grids, refractory plates and stainless steel / cast iron plate are correctly positioned. The diagram illustrates the correct positions for the plates A and grids B. 3 5 C 4 1 A 2 The self-cleaning refractory plates (A) must be fitted on the rests 1 and 2 shown below. The grids (B) or the stainless steel / cast iron plate (C) have two rests of different heights at the rear (3 and 4) on which they can be placed. [. . . ] Instructions for use: spray the product straight onto the dirty surfaces several times. Wipe with a non-abrasive sponge, rinse thoroughly and dry with a soft cloth. For the best results, allow the degreasing detergent to act for some time. To eliminate yellowing, pour Crema inox onto a paper cloth and rub in the direction of the satin-finish. 12. 2 Cleaning the internal barbecue components 12. 2. 1 The ceramic plates The ceramic plates are made from refractory material and are therefore fragile; handle with care to avoid breakage. [. . . ]