User manual SMEG DC122B

[. . . ] INSTRUCTION MANUAL GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents 1. 6. Safety and operating instructions ___________________________ 2 Installation and hook-up___________________________________ 5 Description of the controls _________________________________ 9 Operating instructions ___________________________________ 22 Cleaning and maintenance _______________________________ 34 Troubleshooting ________________________________________ 38 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher. The individual sections are laid out to provide you with a step-by-step guide to all your appliance's functions; the texts are easy to understand and are complete with detailed illustrations. [. . . ] Place dishes in both baskets then load the detergent dispenser than less than the normal amount for a full load. PROGRAM DELAY The PROGRAM DELAY button can be pressed to delay the start of the washing program by 3, 6 or 9 hours, indicated by the PROGRAM DELAY/PROGRAM PHASES (5) lights. This function allows you to set the dishwasher to work at your preferred time of day. After selecting the delay, start the program (see relative section). The appliance will prewash the dishes, after which the "program delay" set previously will come into effect (option light and light of selected program on). N. B. : It is not possible to select the PROGRAM DELAY option once the cycle has begun. Remaining program delay time: with this option active, the user can view the time left before the washing cycle starts. · press the START/PAUSE button (3); the light of the first phase (5) of the selected program (4) comes on, while the program light flashes (confirmation beep); · press the PROGRAM DELAY button. One of the PROGRAM DELAY lights (5) will flash to indicate whether less than 3, 6, 9 or 12 hours are left before the dishwasher starts. 20 User instructions TO SAVE ON ENERGY!AND PROTECT THE ENVIRONMENT · · · · · Always try to run the dishwasher fully loaded. Do not wash the dishes in running water. Use the washing program that is most appropriate for each type of load. Do not carry out any preliminary rinsing. If available, connect the dishwasher to a hot water supply up to 60°C. TO CUT DOWN ON DETERGENT CONSUMPTION!AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity, observe the following: · · separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures; do not pour the detergent directly on the dishes. REMOVING THE DISHES At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket. 21 User instructions 4. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: · · · Adjust the water softening system; Add the regenerating salt; Add the rinse aid and detergent. 4. 1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness 41-60°dF ­ 24-31°dH). SALT When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. The salt container can hold approximately 1. 7 Kg of salt in grains. The container is situated at the bottom of the dishwasher. After removing the lower basket, unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher. [. . . ] Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service. Water heating malfunction The water is not heated or the heating parameters are not correct. [. . . ]