User manual SMEG DI612SD

[. . . ] INSTRUCTION MANUAL GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents 1. 6. Safety and operating instructions ___________________________ 2 Installation and hook-up___________________________________ 5 Description of the controls _________________________________ 9 Operating instructions ___________________________________ 23 Cleaning and maintenance _______________________________ 35 Troubleshooting ________________________________________ 39 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher. The individual sections are laid out to provide you with a step-by-step guide to all your appliance's functions; the texts are easy to understand and are complete with detailed illustrations. [. . . ] Do not wash the dishes in running water. Use the washing program that is most appropriate for each type of load. Do not carry out any preliminary rinsing. If available, connect the dishwasher to a hot water supply up to 60°C. TO CUT DOWN ON DETERGENT CONSUMPTION!AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity, observe the following: · separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures; · do not pour the detergent directly on the dishes. CUSTOMISING YOUR APPLIANCE The electronic control system allows you to customise your appliance in a number of ways. Key (D) allows selection of the customisation required from the list available, by scrolling through the options in succession. The first time, the key must be held down for a short time (active buzzer), press again for access to the water hardness and language choice customisations. Use key (E) to enable (1) / disable (0) the customisation or modify the parameters. To exit the programming function press key (B). The user customisations cannot be accessed if the dishwasher is in "assisted programming" mode (Wizard). 20 User instructions Enable buzzer With this function enabled (1), a buzzer sounds whenever the door is opened and closed with a program running or selected, at the end of the cycle and during programming procedures. If it is disabled (0), the buzzer never sounds. Procedure long press on key (D) Customisation Enable buzzer Settings Enable (1) / Disable (0) H2O hardness Select the water hardness customisation function using key (D). Press (E) in repetition to select the hardness level required (from H0 to H5) with reference to the "WATER HARDNESS TABLE". Procedure long press on key (D) second press on key (D) Customisation Enable buzzer H2O hardness Settings Enable (1) / Disable (0) from h0 to h5 WATER HARDNESS TABLE WATER HARDNESS German Degrees (°dH) French Degrees (°dF) 0-4 5 - 15 16 - 23 24 - 31 32 - 47 48 - 58 0-7 8 - 25 26 - 40 41 - 60 61 - 80 81 - 100 SETTING h0 h1 h2 h3 h4 h5 Contact your local water board for information on the hardness of your water supply. 21 User instructions Language Select the language customisation function using key (D). Press (E) in repetition to select the language required. Procedure long press on key (D) second press on key (D) Customisation Enable buzzer H2O hardness Settings Enable (1) / Disable (0) from h0 to h5 Languages available: Italian English French German Spanish Portuguese third press on key (D) Language selection 22 User instructions 4. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: · · · Adjust the water softening system; Add the regenerating salt; Add the rinse aid and detergent. 4. 1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness 41-60°dF ­ 24-31°dH). SALT When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. The salt container can hold approximately 1. 7 Kg of salt in grains. The container is situated at the bottom of the dishwasher. After removing the lower basket, unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher. Before replacing the cap, remove any salt residues from around the opening. · · When using the dishwasher for the first time, in addition to the salt it is also necessary to add one litre of water to the container. [. . . ] Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service. The water is not heated or the heating parameters are not correct. Repeat the washing program; if the problem persists, contact the after-sales service. [. . . ]