User manual SMEG DW45ST

[. . . ] Operating instructions ____________________________________ 34 4. 1 4. 2 4. 3 4. 4 Using the water softening system ______________________________________________ 34 Using the rinse aid and detergent dispensers _____________________________________ 36 General warnings and recommendations ________________________________________ 38 Using the baskets___________________________________________________________ 39 5. Cleaning and maintenance ________________________________ 42 5. 1 General warnings and recommendations ________________________________________ 42 6. Troubleshooting ________________________________________ 45 Thank you for choosing this product. We advise you to carefully read all the instructions contained in this manual, in order to understand how to operate your dishwasher safely and correctly. [. . . ] To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket. SLIDING FACING PANEL (for "fully integrated" models only) Some dishwashers are equipped with a FRONT DISPLAY carrying the same information as the one on the top control panel. A system which moves the facing panel allows this display to be revealed when the dishwasher door is closed; to do this follow the instructions in the "MOVING THE FACING PANEL" point. While the program is in progress, the display shows the time left before it ends (hours alternating with minutes), and the symbols described in section "3. Description of the controls" and any error warnings E2, E3, . . . The LUMINOUS LOGO remains off throughout the cycle and illuminates when it ends. LUMINOUS LOGO FRONT DISPLAY 32 User instructions MOVING THE FACING PANEL To lower the facing panel and reveal the FRONT DISPLAY, proceed as follows: · Make sure that the door is closed; Push the facing panel down until the whole of the display is visible. To return the facing panel · to the normal position, push it back up. WARNINGS ! · · · · · The facing panel can only be lowered with the door closed; Once the facing panel has been lowered the door cannot be opened (see diagram); Before opening the door of the dishwasher make sure that the facing panel is in the high position; Never lower the facing panel and close the door simultaneously; first close the door, then lower the facing panel; never raise the facing panel and open the door simultaneously; first bring the facing panel to the high position, then open the door. COMPLIANCE WITH THE INSTRUCTIONS PROVIDED ABOVE ENSURES THE CORRECT OPERATION BOTH OF THE SLIDING SYSTEM OF THE FACING PANEL AND OF THE DISHWASHER ITSELF. 33 User instructions 4. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: · Adjust the water softening system; · Add the regenerating salt; · Add the rinse aid and detergent. 4. 1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness 41-60°dF ­ 24-31°dH). SALT When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. The salt container can hold approximately 1. 7 Kg of salt in grains. Use a cloth to remove any spillage of rinse aid which might lead to the formation of excess foam. ADJUSTING THE RINSE AID DISPENSER SETTING The dishwasher is factory set for medium water hardness. However it possible to change the setting by turning the dispenser's selector to the desired position: the amount of rinse aid dispensed is proportional to the selector position. The setting must be increased when the washed dishes appear dull or have circular staining. · · · To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it. Then use a screwdriver to rotate the rinse aid selector to the desired position. Replace the cap, turning it clockwise. 36 User instructions · · The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains. If, on the other hand, the dishes are sticky or have white streaks, it is necessary to reduce the rinse aid setting. ADDING THE DETERGENT To open the detergent dispenser cap, lightly press the button P. Add the detergent and close the cap carefully. During the washing cycle, the dispenser will be opened automatically. · When a SUPER program is selected, in addition to the normal dose of detergent, it is necessary to add an additional amount inside compartment G or H. Use only detergents specially formulated for dishwashers. For optimal washing results it is important to use a good quality detergent. The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results. [. . . ] Troubleshooting The dishwasher is equipped with a self-diagnostics system that is capable of detecting and signalling a number of possible faults. In the event of a fault or malfunction, before calling the After-sales service centre, we suggest that you first consult the troubleshooting guide below. If the problem persists even after implementing the recommended solutions, call the After-sales service centre after having carried out the following: · making a note of the message displayed by the self-diagnostics system; · unplug the power cord from the socket; · shut off the water supply tap. TABLE OF FAULTS DETECTED BY THE SELF-DIAGNOSTICS SYSTEM FAULT DESCRIPTION The system which limits the water level inside the dishwasher (Level Safety Device) has been tripped. Since the cause might be a temporary failure, try reprogramming the dishwasher. [. . . ]