User manual SMEG FC40RX3

[. . . ] 39 BEFORE INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 DESCRIPTION OF FRONT PANEL CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 USING THE OVEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 USING THE PIZZA FUNCTION (ON SOME MODELS ONLY) . . . . . . . . . . . . [. . . ] Press PT2 once to end the cooking process and switch the oven to OFF status. The minute minder also function works with no function set. Warning: the minute minder function does not stop the cooking process. It only warns the user that the preset number of minutes have passed. Modifying the data set Once the countdown has started, its duration can be changed while cooking is in progress. When the symbol is steady and cooking is in progress, press PT1 once. The symbol starts flashing and PT1 can be turned to change the set duration. A few seconds after the last change, the symbol will stop flashing, and the countdown will restart from the new value. To change the preset temperature, wait for the symbol to become steady and turn PT1 to the right or left to increase or decrease the cooking temperature. The symbol and the current time will appear on the display. Turning PT1 to the right increases the time, allowing the cooking start time required to be set. A few seconds after the required duration is set, the and symbols will stop flashing, and the oven will start to wait for the starting time set. Now press PT1 once again and the message «OFF 2300» will appear on DPS1. Turn PT1 to the right or left to activate (ON 2300) or deactivate (OFF 2300) this function, which limits the oven's maximum power absorption, in any function, to 2300 W. After setting the parameter required, press PT2 to return the oven to the initial standby status. 47 Instructions for the User 7. 7 Cooling fan system The appliance is equipped with a cooling system which comes into operation as soon as a cooking function starts. Operation of the fans generates a normal air flow which comes out above and underneath the door and may continue for a short time even after the oven is switched off. 7. 8 Inside light The oven light comes on: · when the oven door is opend in standby status (point «7. 2 Operating modes») or; · when the function knob is turned to any function, except and 48 Instructions for the User 8. USING THE PIZZA FUNCTION (ON SOME MODELS ONLY) This appliance is equipped with a function specially developed for cooking pizza. This function is identified by the symbol on the oven functions knob. To cook a pizza, proceed as described below. With the oven cold, remove the circular cover from the bottom of the oven (fig. 1) and fit the pizza plate in its place (Fig. 2). 1) 2) Press PT2 to switch the oven on, then use PT2 again to select the function. The display will show the recommended temperature for cooking pizza (280°C), (for the 2300W low energy consumption mode the recommended cooking temperature is 260°C). [. . . ] Close the door to an angle of about 45° and lift it off. To reassemble, fit the hinges into their grooves, then lower the door into place and extract the pins. 12. 3 Removing the gasket To allow thorough cleaning of the oven, the door gasket can be removed. 62 Instructions for the User 12. 4 Removing the inside glass with the door cold The glass in the door should always be kept thoroughly clean. For easier cleaning, the door glazing can be fully removed by proceeding as described below. After opening the door and locking it in place as described in point «12. 2 Removing the door», remove the three panes of glass. [. . . ]