User manual SMEG FS9010XS

[. . . ] Contents 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 2. 1 2. 2 2. 3 2. 4 2. 5 General safety instructions Identification plate Manufacturer liability Appliance purpose This user manual How to read the user manual General Description Cooking hob Control panel Other parts Available accessories Instructions First use Using the accessories Using the hob Using the oven Cooking advice Instructions Cleaning the appliance Removing the door Cleaning the door glazing Removing the internal glass panes Vapor Clean Extraordinary maintenance Clearances above and around domestic appliances Gas connection Adaptation to different types of gas Positioning Electrical connection For the installer 4 5 5 6 6 6 2 Description 7 7 8 8 9 9 3 Use 3. 1 3. 2 3. 3 3. 4 3. 5 3. 6 4. 1 4. 2 4. 3 4. 4 4. 5 4. 6 4. 7 5. 1 5. 2 5. 3 5. 4 5. 5 5. 6 11 11 12 13 14 15 16 4 Cleaning and maintenance 19 19 19 20 21 21 23 24 5 Installation 27 27 28 31 32 38 39 We advise you to read this manual carefully, which contains all the instructions for maintaining the appliance's aesthetic and functional qualities. For further information on the product: www. smeg. com 3 EN 1 Instructions 4 Instructions 1 Instructions 1. 1 General safety instructions Risk of personal injury • During use the appliance and its accessible parts become very hot. • Never touch the heating elements during use. • Keep children under eight years of age at a safe distance if they are not constantly supervised. [. . . ] • Do not use rough or abrasive materials or sharp metal scrapers. • Do not wash the removable components such as the cooktop grids, flame-spreader crowns and burner caps in a dishwasher. 4. 2 Cleaning the appliance We recommend the use of cleaning products distributed by the manufacturer. Recommendations for cleaning the cooktop To keep the surfaces in good condition, they should be cleaned regularly after use. Let them cool first. 19 EN 4 Cleaning and maintenance Cleaning the cooktop Cleaning and maintenance Cleaning the igniters and thermocouples • If necessary, clean the igniters and thermocouples with a damp cloth. • If there is any dry residue, remove it with a toothpick or needle. 4. 3 Removing the door For easier cleaning, the door can be removed and placed on a tea towel. To remove the door proceed as follows: 1. Open the door completely and insert two pins into the holes on the hinges indicated in the figure. Recommendations for cleaning the oven cavity For the best oven upkeep, clean it regularly after having allowed it to cool. Avoid letting food residue dry inside the oven cavity, as this could damage the enamel. Take out all removable parts before cleaning. For easier cleaning, we recommend removing: • The door • The rack/tray support frames • The oven seal. In the event you are using specific cleaning products, we recommend running the oven at maximum temperature for 15-20 minutes in order to eliminate any residue. 2. Grasp the door on both sides with both hands, lift it forming an angle of around 30° and remove it. 20 Cleaning and maintenance 3. To reassemble the door, put the hinges in the relevant slots in the oven, making sure that grooved sections A are resting completely in the slots. Lower the door and once it is in place remove the pins from the holes in the hinges. For easier cleaning the door internal glass panes can be disassembled. Remove the internal glass pane by pulling the rear part gently upwards, following the movement indicated by the arrows (1). In this way, the 4 pins attached to the glass detach from their housings in the oven door. 4. 4 Cleaning the door glazing The glass in the door should always be kept thoroughly clean. In case of stubborn dirt, wash with a damp sponge and an ordinary detergent. Some models have an intermediate glass pane. Remove the intermediate glass pane by lifting it upwards. 21 EN 4. 5 Removing the internal glass panes Cleaning and maintenance 4. Clean the external glass pane and the panes previously removed. In case of stubborn dirt, wash with a damp sponge and neutral detergent. [. . . ] • Do not pull the cable to remove the plug. • Use cables withstanding a temperature of at least 90°C. • The tightening torque of the screws of the terminal board conductors must be 1. 5 - 2 Nm. General information Check the grid characteristics against the data indicated on the plate. [. . . ]