User manual SMEG GL75XG

[. . . ] INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION: COOKING AND HEATING FOODS; ALL OTHER USES ARE TO BE CONSIDERED IMPROPER. THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN THOSE STATED ABOVE. [. . . ] Carefully trim off the excess edge of the gasket B. The dimensions in the drawing below refer to the hole on the inside edge of the gasket. See right for the precise holes to be used when securing the hob to the top correctly using the brackets. 22 Instructions for the Installer 3. Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations. Check that the power supply line is properly earthed. Pass the power supply cable through the rear of the cabinet, taking care that it does not touch the bottom case of the hob, or the oven (if any) built in underneath it. The appliance's power supply line must be fitted with an omnipolar breaking device with contact gap of at least 3 mm, located in an easily accessible position close to the appliance itself. The use of reductions, adapters or junctions is not recommended. If the power supply cable has to be replaced, the gauge of the wires in the new cable must be at least 0. 75 mm2 (3 x 0. 75 cable), bearing in mind that the earth wire (yellow-green) must be at least 20 mm longer at the end for connection to the appliance. Use only a type H05V2V2-F or similar cable resistant to a temperature of up to 90°C. The cable must be replaced by a qualified electrician, who must make the mains connection as shown below. L = brown N = blue = yellow-green The power supply lead must be replaced by an authorised service centre to prevent all risks. The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance. 23 Instructions for the Installer 4. Gas connection If the appliance is installed above an over, the gas hose must be passed around the back of the oven to prevent overheating. The connection to the gas mains may be made using a copper pipe or a continuous-wall steel hose in accordance with the relevant regulations. To simplify connection, the horizontal position of the fitting A on the back of the appliance is adjustable. Some models may have 2 additional pins at the side (Fig. 5), which must be removed in the same way, using a tool to apply leverage to the hob. Fig 1) Fig 2) Fig 3) Fig 4) Fig 5) 26 Instructions for the Installer 5. 2 Adjusting for bottled gas Undo the screw A and push the support B fully down. Remove the nozzle C with a spanner and fit the suitable one following the instructions in the tables referring to the type of gas to be used. The nozzle must not be tightened with a torque of more than 3 Nm. Return the support B to its original position, so that the nozzle C is perfectly covered. Regulate the air flow by moving the Venturi pipe D until the distance "X" stated in point "5. 5 Adjusting the primary air flow" is obtained and secure it with the screw A. When the adjustments are complete, restore the seals with wax or an equivalent material. Burner Nominal heat capacity (kW) Nozzle diameter 1/100 mm Bottled gas ­ G30/G31 30/37 mbar By-pass mm 1/100 30 33 50 50 50 65 30 55 30 55 Auxiliary Semi rapid Rapid (3) Rapid (7) Rapid (6) Ultra-Rapid Double Internal Crown (4) External Double Crown (8) Internal External 1. 05 1. 7 3. 5 2. 9 3. 1 4. 2 0. 9 3. 3 0. 9 4. 0 48 62 89 80 85 98 45 87 45 95 Reduce Capacity Capacity d heat g/h G30 g/h G31 capacity (W) 400 76 75 500 124 121 1050 254 250 1050 211 207 1050 225 221 1600 305 300 400 1200 400 1200 62 240 62 291 61 236 61 286 5. 3 Adjusting for natural gas The appliance is tested with G20 (2H) natural gas at the pressure of 20 mbar. The diameters of the bypasses for each individual burner are stated in point "5. 2 Adjusting for bottled gas". After adjusting for use of a gas other than the gas used for testing the appliance, replace the label on the casing with the label for the new gas. The label is supplied in the bag with the LPG nozzles (G30 ^ G31). 28 Instructions for the Installer 5. 8 Hob burner layout Burner type 1 Auxiliary 2 Semi rapid 3 Rapid 4 Double flame 5 Ultra rapid 6 Rapid 7 Rapid 8 Double flame 5. 9 Greasing the gas taps Over time, the gas taps may become stiff or jam. Clean their insides and change their lubricating grease. [. . . ] 8. 1. 2 Food stains or spills Never use metal scouring pads or sharp scrapers which will damage the surface. Use ordinary non-abrasive products for steel, with the aid of non-scratching sponges and wooden or plastic utensils if necessary. Rinse thoroughly and dry with a soft cloth or chamois leather. 8. 2 Cleaning the components 8. 2. 1 The knobs The knobs and front panel must be cleaned with a soft cloth dipped in warm water and dried thoroughly. The knobs can easily be removed by pulling them outwards. [. . . ]