User manual SMEG GW3060P60

[. . . ] 8 3. 1 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AVAILABLE ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USING THE OVEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5. 1 Warnings and general advice for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ON setting: from the stand-by setting, press PT2 once. All the displays and knobs light up. OFF setting: from the ON position, keep PT2 pressed until it turns off. symbol on DSP1 remains 5. 4 First use When using for the first time, or after a power failure, the oven's left hand-display, DSP1, will show a flashing symbol. To start any cooking operation, the current time must be set. 5. 4. 1 Setting the current time Adjusting the current time: · turn PT1 to the right and left to increase or decrease the hours respectively. (If the knob is held in one direction the time changes faster). · when PT1 is released, after a few seconds the display will stabilize and only the two dots that separate the hours from the minutes will flash, indicating it is working properly. (The display will also show the symbol ). Note: It might become necessary to change the current time, for example at daylight savings time. Starting from the stand-by setting, (see paragraph "5. 3 Operating modes"): · · hold down PT1 for a few seconds until the symbol stops flashing. repeat the operations described in paragraph "5. 4. 1 Setting the current time". 5. 5 Selecting a function In the ON status only, a cooking function can be selected by simply turning PT2 to the right or left. The selected function will change color to red on the display. After the selection, the preset cooking temperature will be displayed on DSP2. Modifying the setting Once semiautomatic cooking has started, its duration can be changed. When the symbol is steady on and cooking is in progress, press PT1 once. The symbol starts flashing and PT1 can be turned to change the set duration. A few seconds after the last change, the symbol will stop flashing, and semiautomatic cooking will restart from the new value. To change the preset temperature, wait for the symbol to become steady and turn PT1 to the right or left to increase or decrease the cooking temperature. 15 Instructions for the user 5. 6. 2 Automatic cooking Automatic cooking is the function which allows a cooking operation to be started at a set time and then ended after a specific length of time that is set by the user. Select a cooking function, set the desired cooking temperature or leave the preset temperature (see paragraph "5. 5 Selecting a function") and press PT1 twice. The display will show the figures and the symbol (flashing). Turn PT1 to the right or left to set the cooking time (from 00:01 to 23:59). For safety reasons, when setting automatic cooking the user must first program a cooking duration and then set the cooking start time. It is not possible to set just the cooking start time, without setting the cooking duration. After setting the duration, press PT1 once. The symbol and the current time will appear on the display. [. . . ] SPECIAL MAINTENANCE The oven may require special maintenance or replacement of parts subject to wear such as seals, bulbs, etc. The following instructions describe how to do these minor maintenance operations. ELECTRICAL SHOCK HAZARD Before any maintenance operation, disconnect the power supply of the appliance. WARNING 9. 1 Replacing the oven light Remove upper oven protection A and ring B as well as the glass cover C, unscrewing it anticlockwise. Reassemble ring B, cover C and upper protection A. CAUTION: The standard bulbs are halogen: do not touch them directly with your fingers. [. . . ]