User manual SMEG GW3060SC6

[. . . ] 7 BEFORE INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 DESCRIPTION OF FRONT PANEL CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 USING THE OVEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 USING THE PIZZA FUNCTION (ON SOME MODELS ONLY) . . . . . . . . . . . . [. . . ] To do this, starting from the standby setting (see point "7. 2 Operating modes") keep PT1 pressed until the figures on DSP1 flash. Now repeat the operations described in point "7. 3. 1 Setting the current time". 7. 4 Selecting the function In the ON state only, a cooking function can be selected by simply turning PT2 to the right or left. The function selected will change colour to red on DSP3. The preset cooking temperature will be displayed on DSP2. 7. 4. 1 Cooking with preset temperature After selection of the function required, the oven will start the cooking procedure at the preset temperature. Cooking itself is preceeded by a preheating stage, which allows the oven to heat to the cooking temperature more quickly. The ° symbol flashes on DSP2 to indicate that this stage is in progress. The symbols will light up one at a time, from the bottom up, indicating the rise in the temperature inside the oven. When the preheating stage is over, the ° and symbols will remain constantly on to indicate that the food can be placed inside the oven. 7. 4. 2 Changing the preset temperature The temperature preset for each function can be changed to suit the user's requirements. At any time while cooking is in progress, turn PT1 in either direction to increase or decrease the cooking temperature by 5 degrees at a time. A few seconds after the last change, the e symbols will appear (in steady mode) on DSP1 and automatic cooking will restart with the new settings. Once cooking has been programmed, before it starts all the lamps on the control panel will be on, except for DSP2 which will illuminate when cooking has started, showing the set temperature. 7. 6 Secondary menu This appliance also has a concealed "secondary menu" allowing the user to: 1 Activate or deactivate the child safety device ( ); 2 Activate or deactivate the Show Room function (which disables all the heating elements so that only the control panel works); 3 Activate or deactivate the function which limits the maximum power absorption to 2300 W; 7. 6. 1 Child safety lock-out function With the oven in OFF status (see point "7. 2 Operating modes") keep PT1 pressed until the message OFF SHO appears on DSP1. Now press PT1 until the message "OFF BLOC" appears on DPS1. Turn PT1 to the right or left to activate (ON BLOC) or deactivate (OFF BLOC) this function, which locks out all the functions and knobs after 3 minutes of operation without any command from the user (when this system is active, the symbol appears on DPS2). After setting the parameter required, press PT2 to return the oven to the initial standby status. To exit the lockout status temporarily to modify a cooking program or select a different function, keep PT1 pressed until the symbol disappears from DSP2. The required changes can now be made, and 3 minutes after the last setting is made the lockout will come into operation again. To deactivate the lockout permanently, access the secondary menu and switch the function off as described in this section. 14 Instructions for the User 7. 6. 2 Show Room Function With the oven in OFF status (see point "7. 2 Operating modes") keep PT1 pressed until the message OFF SHO appears on DSP1. This means that the SHOW ROOM function (which disables all the heating elements so that only the control panel works) is not active. Turn PT1 to the right or left to activate (ON SHO) or deactivate (OFF SHO) this function. After setting the parameter required, press PT2 to return the oven to the initial standby status. [. . . ] Replace the protective cover A. Use only light bulbs approved for ovens (T 300°C). 26 Instructions for the User 12. 2 Removing the door 12. 2. 1 With type 1 mobile levers With the door completely open, lift the levers A of the two hinges until they touch the hinges B and take hold of the two sides of the door with both hands close to the hinges themselves. Raise the door to an angle of about 45° and remove it. If the hinges have not locked, repeat the operation, raising the levers and keeping the door slightly raised. To reassemble, fit the hinges B into their grooves, then lower the door into place, ensuring that it remains fitted into the grooves C, then lower the levers A. 1) 12. 2. 2 Removing doors with pins Open the door completely and insert the pins (supplied) into the holes from the inside. [. . . ]