User manual SMEG GW4060S

[. . . ] This user-friendly manual will provide answers to all your questions about use of the dishwasher. For any other information about use and maintenance of the dishwasher, read the enclosed manual carefully. USER INSTRUCTIONS: useful information is provided for the use of the washing programs and all the dishwasher's functions. User instructions 1. Description of the controls 1. 1 Upper panel All the dishwasher controls are grouped on the upper panel. procedures are only possible when the door is open. 1 ON/OFF BUTTON Pressing this button energises the appliance. [. . . ] AFTER INSTALLATION THE DISCONNECTION DEVICE HAS TO BE EASY TO REACH. THE CONNECTION TO THE MAINS MUST BE CARRIED OUT BY A QUALIFIED TECHNICIAN IN ACCORDANCE TO THE SCHEME SHOWN BELOW AND THE REGULATIONS IN FORCE. L = brown N = blue = yellow-green In the event of damage to the supply cord, have it replaced by the manufacturer or an Authorized Technical Service Centre in order to avoid any risk. Installation instructions WHEN CLEANING AND MAINTAINING THE APPLIANCE: BEFORE CARRYING OUT ANY WORK, ALWAYS UNPLUG THE APPLIANCE FROM THE ELECTRICAL SUPPLY OR SWITCH OFF THE ALL-POLE DISCONNECTION DEVICE. FOR GREAT BRITAIN ONLY: THIS APPLIANCE MUST BE EARTHED. Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A. S. T. A. approved fuse to BS 1362 type and proceed as follows: 1. Fit replacement 13A fuse into fuse cover. Refit both into plug. The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be used until a correct replacement is fitted. Correct replacement are identified by the colour insert or the colour embossed in words on the base of the plug. Replacement fuse covers are available from your local electrical store. User instructions 3. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: Adjust the water softening system; Add the regenerating salt; Add the rinse aid and detergent. 3. 1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness 41-60dF 24-31dH). SALT When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. The salt container can hold approximately 1. 7 Kg of salt in grains. To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it. Then use a screwdriver to rotate the rinse aid selector to the desired position. The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains. If, on the other hand, the dishes are sticky or have white streaks, it is necessary to reduce the rinse aid setting. User instructions ADDING THE DETERGENT To open the detergent dispenser cap, lightly press the button P. Add the detergent and close the cap carefully. During the washing cycle, the dispenser will be opened automatically. When a program with hot prewash is selected (see program table), extra detergent must be placed in the cavity G/H (depending on models). Use only detergents specially formulated for dishwashers. For optimal washing results it is important to use a good quality detergent. The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results. Once opened the detergent packs should not be kept for too long, otherwise the detergent loses its effectiveness. Do not use detergents formulated for washing dishes by hand, because they produce a great deal of foam and may negatively affect the operation of the dishwasher. [. . . ] 4. Questo blocco di lavaggio dotato di un dispositivo che permette di regolare la planarit dell'apparecchio una volta posizionato. Tirare il cassetto basso di destra estraendolo completamente e sollevandolo verso l'alto come un normale cassetto (Fig. 1); Togliere lo zoccolo inferiore sfilandolo verso l'alto e successivamente verso l'esterno (Fig. 2); Con una chiave a tubo di 10 ruotare i dadi esagonali, illustrati nella figura a lato, fino ad ottenere la planarit rispetto al pavimento (Fig. 3); Rimontare lo zoccolo avendo cura prima di infilare le due viti in basso e incastrarlo poi con le due in alto (Fig. 4) This washing unit is equipped with a device allowing it to be levelled after positioning. Completely remove the bottom right-hand drawer by pulling it out and then lifting it like an ordinary drawer (Fig. 1); Remove the bottom plinth by first lifting it and then pulling it away from the appliance (Fig. 2); Use a 10 socket wrench to turn the hexagonal nuts shown in the photograph until the unit is levelled in relation to the floor (Fig. 3); Replace the plinth, first taking care to insert the two bottom screws, and then fixing it with the two top screws (Fig. 4). [. . . ]