User manual SMEG HBE64CGS

[. . . ] The above informations give to the technical assistant the possibility to get fit spare parts and a heavensent intervention. We suggest to fill the table below. MARK:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MODEL:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SERIES:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Normal plate Ø 145 of 1000 W 2 Normal plate Ø 180 of 1500 W 3 Rapid plate Ø 145 of 1500 W 4 Rapid plate Ø 180 of 2000 W 5 Thermostat plate Ø 145 of 1500 W 6 Thermostat plate Ø 180 of 2000 W 7 Control knob for electric plate n° 1 8 Control knob for electric plate n° 2 9 Control knob for electric plate n° 3 10 Control knob for electric plate n° 4 11 Control knob for electric plate n° 5 12 Control knob for electric plate n° 6 13 Warning light indicating that one or more plates are operating 2 11 TECHNICAL DATA MODEL WITH 2 RAPID PLATES + 2 THERMOSTAT PLATES VOLTAGE FREQUENCY TOT. [. . . ] Never touch them with the hands or other objects in order to prevent scorching. - If the appliance has a glass lid, this could shatter when the cooker becomes hot. Always disconnect all the plates before closing the lid. - Immediately disconnect the appliance from the electricity main as soon as cracks are noted on the surfaces of the plates. SERVICING Always disconnect the appliance from the electricity main before proceeding with any servicing operation. conductor longer than "live" ones, and must respect the cautions in paragraph "Electrical connection". To reassemble the appliance repeat the inverse process. 8) REPLACING THE ELECTRICAL COMPONENTS For access to the various parts, remove the hotplate from the top of the cabinet. Then overturn it, unscrew screw "Z" and remove under part. After these actions is possible to work on the plates, commutators, clamps and input cable. In case of substitution of the input cable, the installer must keep the "earth" 9) TECHNICAL CHARACTERISTICS OF THE ELECTRICAL COMPONENTS To facilitate the job of the installer we present a scheme with the characteristics of the components. POWER OF ELECTRICAL COMPONENTS DENOMINATIONS W Denominations Normal plate Ø 145 mm ­ 7 positions with the protector Normal plate Ø 180 mm ­ 7 positions with the protector Rapid plate Ø 145 mm ­ 7 positions Rapid plate Ø 180 mm ­ 7 positions Thermostat plate Ø 145 mm ­ 12 positions Thermostat plate Ø 180 mm ­ 12 positions W 1000 1500 1500 2000 1500 2000 TYPE AND SECTION OF THE POWER CABLES Cable type Single phase power 230 - 240~ 3 X 1. 5 mm2 (*) 5 X 1. 5 mm2 (*) Polycroropene H05 RN-F 3 X 2. 5 mm (*) 2 Three phase power 400 - 415 V 3N~ Three phase power 400 - 415 V 2N~ Rubber H05 RR-F 4 X 1. 5 mm2 (*) (*) keeping in mind the contemporaneousness factor FIG. 3 4 9 CONVERSIONS Disconnect the appliance from the mains supply prior to any conversions being carried out. b) Shift connecting plate on terminal according to the following chart. c) Insert a supply cable of adequate section (see chart par. 10) through core hitch on the terminal board. d) Connect the phase and earth wires to the relative terminal board. e) Fix the supply cable in place using clamp. f) Refit the hotplate, complying with the above instructions in reverse. CLEANING IMPORTANT: Always disconnect the appliance from the electricity main before carrying out any cleaning operation. WARNINGS: - Correctly preserve the plate after use by treating it with special products, easily available on the market. This will keep the surface of the plate clean and bright. The operation will also prevent the formation of rust. - Any liquid overflowed the pans, must be always remove with a rag. 7) CHANGING THE TYPE OF POWER SUPPLY Although they leave our factory preset for singlephase connection, certain appliances may by converted to the threephase system. Comply with the following instructions: a) Remove the hotplate from the top of the cabinet, overturn it, unscrew screw "Z" and remove under part (see fig. 9). 3) HOTPLATE If you want to preserve the surface clean and bright, periodically wash the hot plate with lukewarm soapy water. [. . . ] This circuit-breaker should be sized according to the rating of the appliance and the opening between its contacts should be at least 3 mm. - Remember that the earth wire must not be cutout by the switch. - Alternatively, the electrical connection may also be protected by a high sensitivity differential switch. Installers are strongly advised to connect the yellow- green earthing wire to an efficient earthing system. [. . . ]