User manual SMEG HTY611DSUK

[. . . ] Summary 1 PRECAUTIONS FOR SAFETY AND USE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. 1 Trademark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. 2 Name and address of manufacturer or distributor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. 3 Declaration of conformity to product standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When -------- appears on the display, release the button and press it again to access the main PCB setup menu. With the tank full/the hood open 1 - Press the button and hold it down for 5/7 seconds. When -------- appears on the display, release the button and press it again to access the main PCB setup menu. All the modifiable parameters can now be displayed, scrolling through them with the Press the button to select the value required for each parameter. button. To confirm the value required simply quit the menu or move on to the next parameter by pressing Quitting the setup menu automatically: wait about 3 minutes without using the controls. Quitting the setup menu in manual mode: hold the ON/OFF button until the beep sounds; the dishwasher switches off. . 11 4. 2 Modifiable parameters The illustrations are purely guideline. The minimum and maximum temperatures available depend on the model (glass washer, dishwasher, undercounter or hood-type model, . . ). Rinsing temperature (boiler temperature) Washing temperature (tank temperature) Warning: The tank and boiler temperatures shown on the display may be different from the actual temperatures by a few degrees, especially in transient phases (just after the FILL is completed, just after the end of the cycle, etc. ) due to the inertia of the measurement probe. Adjusting rinse aid dispensing (optional if installed) Every time is pressed, the value increases of 0, 1 g/l up to a max. Default: 1, 2 g/l. Adjusting detergent dispensing (optional if installed) From 0, 0 g/l to 3, 0 g/l every time is pressed, the value increases of 0, 2 g/l. Beyond 3, 0 g/l every time is pressed, the value increases 1, 0 g/l up to 10, 0 g/l (maximum value). Factory-set default value = 2 gr/lt. 12 Autostart function Set at “on” to start the cycle when the hood/door is closed. Set at “off” to start the cycle after confirmation with the start button . Regeneration frequency setup (models with softener)   (Default value: H03; modify the parameter to suit the mains water hardness. At first use, the salt tank has to be filled. It is subsequently sufficient simply to fill up with regenerating salt when necessary. Hardness Hardness (°dF Setting (°dH German French level degrees) degrees) Regeneration off Regeneration off H00 H01 H02 H03 H04 H05 Important: During normal operation, the dishwasher will perform a number of washing cycles while regeneration is in progress. During this time (5-6 cycles) the intake 33, 5 60 H06 water will not be treated, but this will not affect the washing quality. With values over 60°f an external water treatment device must be used and the regeneration frequency must be set on H00. 8, 5 11 17 22, 5 28 15 20 30 40 50 Extra rinse Rinsing is 10” longer than the standard in each washing cycle. On: enabled – OFF: disabled. 13 "Clean water" cycle With this option clean water is used for every washing. At each cycle, the washing water is completely drained and it is replaced with clean water from rinsing. N. B. : prolonged use of this option leads to higher detergent and rinse aid consumption. Thermostop Set as “on” = minimum rinsing temperature as set, (see boiler temperature above) regardless of intake water temperature; the cycle duration may be a few seconds longer than the nominal length. Set as “off” = the minimum rinsing temperature might be a few degrees lower than the setting if hot intake water is not used. If the thermostop device is set “off” the rinsing °t are no longer monitored and the user is responsible for ensuring that the minimum correct °t are maintained for the tank and boiler. It is particularly important to check the intake water temperature. Also refer to the insufficient washing/drying /foam in tank point of the “troubleshooting” section : restore °t Stop ON and/or connect the appliance to a hot water supply. High speed (FST) or economy (ECO) filling (FILL) Fast start (FST): starts the dishwasher in less than the standard time; leads to higher water consumption for the first cycle start. Eco start (ECO): starts the dishwasher in standard time, with no added water consumption. On: enabled – OFF: disabled. Cycles performed counter Shows the count of the total cycles performed by the dishwasher since installation. [. . . ] (10. 2 Periodical checks) Clogged filter Insufficient or improper detergent or rinse aid. Read “cleaning the filters during the day” Verify detergent type and quantity. Failing or insufficient use of detergent or rinse aid: the detergent or rinse aid cannot be withdrawn from the dedicated containers. Worn or broken internal tube for detergent or rinse aid of the peristaltic pump, to be replaced by the After-Sales Service. This ordinary maintenance service is recommended at least once a year for the correct functioning of the dosers. Place dishes / glasses correctly. POOR WASHING RESULTS Badly positioned dishes / glasses. Low washing temperature Verify the temperature displayed, if it is inferior than 50°C contact customer Support. Increase the duration of the washing cycle, especially if the load is very dirty or partially dried. [. . . ]