User manual SMEG IGS600W

[. . . ] 22 MANUTENO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2 2 RECOMMENDATIONS AND SUGGESTIONS The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. INSTALLATION The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. The minimum safety distance between the cooker top and the extractor hood is 650 mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation). [. . . ] For Class I appliances, check that the domestic power supply guarantees adequate earthing. Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm. The route of the flue must be as short as possible. Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc. ). If the extractor is used in conjunction with non-electrical appliances (e. g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air. USE The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells. Never use the hood for purposes other than for which it has been designed. Never leave high naked flames under the hood when it is in operation. Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides. Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. Adjust the screws Vr to level the hood body. Vr 12a Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe 150 or 120 mm, the choice of which is left to the installer. To install a 120 mm air exhaust connection, insert the reducer flange 9 on the hood body outlet. Fix the pipe in position using sufficient pipe clamps (not supplied). Remove possible charcoal filters. 150 9 120 RECIRCULATION VERSION AIR OUTLET Push fit connection 15 onto the hood body outlet. Insert the connection extension pieces laterally 14. 1 in connection 15. Make sure that the outlet of the extension pieces 14. 1 is horizontally and vertically aligned with the chimney outlets. If this is not the case, adjust the position by either reversing the connection extension pieces 14. 1 and then reassemble as described previously. Ensure that the activated charcoal filters have been inserted. 15 14. 1 EN 6 6 ELECTRICAL CONNECTION Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. Chimney assembly Upper chimney section Slightly widen the two sides of the upper chimney and hook them behind the brackets 7. 2. 1, making sure that they are properly housed. Secure the sides to the brackets using the 4 screws 12c (2, 9 x 9, 5) supplied. Lower chimney section Slightly widen the two sides of the section and hook them between the upper section and the wall, making sure that they are properly housed. [. . . ] Lower chimney section Slightly widen the two sides of the section and hook them between the upper section and the wall, making sure that they are properly housed. Fix the sides of the bottom section to the hood body using the 2 screws 12c (2, 9 x 9, 5) supplied. When installing the recirculation version, fit the directional grills 8a 8b in their housings so that the directional symbols are at the top and towards the front of the hood. Ensure that they are inserted correctly in the outlet connection piece 15. 2. 1 2 8b 2. 2 7. 2. 1 12c 8a 12c EN 7 7 USE L S V1 V2 V3 L S V1 . [. . . ]