User manual SMEG KIV90XT

[. . . ] 21 NDICE PT CONSELHOS E SUGESTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 CARACTERSTICAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 INSTALAO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 UTILIZAO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Mark the centres of the holes in the template. Drill the holes at the points marked: For concrete ceilings, drill for plugs appropriate to the screw size. For hollow brick ceilings with wall thickness of 20 mm: drill 10 mm(immediately insert the Dowels 11 supplied). For wooden beam ceilings, drill according to the wood screws used. For the power supply cable feed, drill 10 mm. For the air outlet (Ducted Version), drill according to the diameter of the external air exhaust duct connection. Insert two screws of the following type, crossing them and leaving 4-5 mm from the ceiling: For concrete ceilings, use the appropriate plugs for the screw size (not provided). for Cavity ceiling with inner space, with wall thickness of approx. For wooden beam ceilings, use 4 wood screws (not provided). For wooden shelf, use 4 screws 12g with washers 22 and nuts 23, provided. EN 6 6 Fixing the frame Loosen the two screws fastening the lower chimney and remove this from the lower frame. Loosen the two screws fastening the upper chimney and remove this from the upper frame. If you wish to adjust the height of the frame, proceed as follows: Unfasten the metric screws joining the two columns, located at the sides of the frame. Adjust the frame to the height required, then refit all the screws removed as above. Insert the upper chimney stack from above, and leave it running free on the frame. Lift up the frame, fit the frame slots onto the screws up to the slot end positions. Tighten the two screws and fasten the other two screws provided with the hood. Before tightening the screws completely it is possible to adjust the frame by turning it. Make sure that the screws do not come out of their seats in the slotted holes. The frame mountings must be secure to withstand the weight of the hood and any stresses caused by the occasional side thrust applied to the device. On completion, check that the base is stable, even if the frame is subjected to bending. In all cases where the ceiling is not strong enough at the suspension point, the installer must provide strengthening using suitable plates and backing pieces anchored to the structurally sound parts. 1 1 2 2 Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe 150 or 120mm, the choice of which is left to the installer. To install a 150 pipe To install the dumper 10 Fix the pipe in position using sufficient pipe clamps (not supplied). [. . . ] CHANGING THE ACTIVATED CHARCOAL FILTER Resetting the alarm signal Press any of the buttons except the Light button. Changing the Filter Remove the Metal grease filters. Remove the saturated Activated Charcoal filter, as shown in the figure. Fit the new Filter, hooking it into place. [. . . ]