User manual SMEG KSIV960X1

[. . . ] The wall/ ceiling must be strong enough to take the weight of the hood. Do not tile, grout or silicone this appliance to the wall. Do not fix chimney flue to furniture or fly over shelves unless the chimney flue can be easily removed, in case maintenance is ever required. 5-6-7 Preliminary information for installing the hood Assembling the deflector (Fig. [. . . ] 1 1 Control panel 2 Grease filter 3 Grease filter release handle 4 Halogen lamp 5 Vapour screen 6 Telescopic chimney 7 Air outlet (used for filter version only) Operation Model with electronic controls Operation Model with button panel A B C D H DEF G D C EAB 8 9 1 1234- 2 34 567 5- 67- 89- Motor OFF button ON button and motor speed selection button 1 - 2 - 3 1-2-. . . . Speed 1 LED Speed 2 LED and metal grease filter saturation LED (in this latter case, the LED will flash - See instructions on grease filter cleaning). Once the grease filters have been cleaned, press button 1 for about 3 seconds until you hear the acoustic signal (beep): the LED 4 will now stop flashing. Speed 3 LED and active carbon filter saturation LED (in this latter case, the LED will flash - See instructions on active carbon filter replacement). Once you have replaced the charcoal filter, press button 1 for about 3 seconds until you hear the acoustic signal (beep). The active carbon filter saturation LED is not activated. In order to activate the active carbon filter saturation indicator, press buttons 2 and 7 simultaneously for 3 seconds. Initially, only LED 4 will flash, then after the 3 seconds have passed, LED 5 will also start flashing, indicating that the active carbon filter saturation control system is active. To switch off the system, re-press the same two buttons: after 3 seconds LED 5 will stop flashing and the device will be switched off. Intensive speed LED Intensive speed ON switch This speed should be used when the concentration of cooking fumes or odours is particularly strong (for example when frying, cooking fish etc. ). The fast speed will run for about 5 minutes and then return to the speed previously set automatically (1, 2 or 3), or switch off if no speed was selected. To turn off the fast speed, before the end of the 5 minutes, press button 1 or button 2. on/off aspiration switch and minimum power selection B+C. medium power selection aspiration switch B+D. maximum power selection aspiration switch E. operating gauge (foreseen in the model with round buttons) a bc d e a. e. on/off light switch off aspiration switch minimum power selection aspiration switch medium power selection aspiration switch maximum power selection aspiration switch If the hood fails to operate correctly, briefly disconnect it from the mains power supply for almost 5 sec. Then plug it in again and try once more before contacting the Technical Assistance Service. 13 Functioning - Model with display Operation All cooker hood versions $ % &' ( ) * A OFF key (Display off) /Stand-by (led lit on the display) press for a long time to select the function desired. C - Timer for selected speed (visualizes the speed selected and flashing LED on the lower side of the display). This knob permits the operation of the cooker hood for a established period: 20 minutes if the speed selected is 1 15 minutes if the speed selected is 2 10 minutes if the speed selected is 3 5 minutes if the intensive speed P is selected. D - Display showing: Fan speed (1-3-P). Change grease filters (grease filter saturation indicator - F) After washing the anti-grease filter, depress knob A for about 3 seconds. [. . . ] The use of a free flame is damaging to the filters and may cause fire accidents, therefore free flame cooking must be avoided. Frying of foods must be kept under close control in order to avoid overheated oil catching fire. Carry out fumes discharging in accordance with the regulations in force by local laws for safety and technical restrictions. This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). [. . . ]