User manual SMEG KSMD910X

[. . . ] Installation Preliminary information for installation of the hood: Disconnect the hood during electrical connection, by turning the home mains switch off. remove the fat/s filter/s and the carbon filter frame. Do not tile, grout or silicone this appliance to the wall. Do not fix chimney flue to furniture or fly over shelves unless the chimney flue can be easily removed, in case maintenance is ever required. [. . . ] Fix the flue units definitively to the suction unit with the screws (consult the figure corresponding to the model in possession) (Fig. Check that the lower section of the flue fits onto the central bracket (Fig. Fix the upper section of the flue units to the flues support bracket with two screws (Fig. Electrical connection The electrical tension must correspond to the tension noted on the label placed inside the cooker hood. Connect the electrical plug, where provided, to the an easily accessible outlet in conformity with local standards in force. Where an electrical plug is not provided (for direct connection to electrical network) place a standards approved bipolar switch with an aperture distance of not less than 3mm (accessible) from the contacts. 1 1 Control panel 2 Grease filter 3 Grease filter release handle 4 lamp 5 Vapour screen 6 Telescopic chimney 7 Air outlet (used for filter version only) 8 point lighting (only for the model in Fig. Operation All cooker hood versions Use the high suction speed in cases of concentrated kitchen vapours. It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking. On/off light switch on/off aspiration switch and minimum power selection medium power selection aspiration switch maximum power selection aspiration switch Fan off (Stand by) Timer for selected speed (visualizes the speed selected and flashing LED on the lower side of the display). This knob permits the operation of the cooker hood for a established period: 20 minutes if the speed selected is 1 15 minutes if the speed selected is 2 10 minutes if the speed selected is 3 5 minutes if the intensive speed P is selected. The letter F will disappear from the display. change activated carbon filters (carbon filter saturation indicator - C). After replacing the charcoal filter, depress knob B for about 3 seconds. The letter C will disappear from the display. When the led in the lower right side is on, it indicates that the cooker hood is ready for operation (standby position), the flashing LED indicates that the timer has been activated for selected speed. Initially, only letter F will fbe displayed, then after the 3 seconds have passed, letter C will be displayed as well, indicating that the carbon filter saturation control system is active. To switch off the system, re-press the same two buttons: letter C appear on display and after 3 seconds letter it disappear and the device will be switched off. Knob to decrease the speed: from intensive speed P to speed level 1. Knob to increase (standby) speed to intensive speed P. Intensive speed P has a duration of 5 minutes after which the cooker hood automatically sets the speed to level 2 (suction power). Speed 1 LED Speed 2 LED and metal grease filter saturation LED (in this latter case, the LED will flash - See instructions on grease filter cleaning). [. . . ] Quite el agua que haya quedado en el filtro sin estropearlo, después quite el almohadillado situado en el interior del armazón de plástico y póngalo en el horno a 100°C durante diez minutos para secarlo completamente. Notice d'installation du moteur groupe Installation instructions of the motor unit Anweisungen für die Installation der Motoreinheit Instructies voor het installeren van de motor-unit Instrucciones para instalación del grupo motor Istruzioni di installazione del gruppo motore Instruções de instalação do grupo motor Instruktioner för installation av motorenheten Veiledning for installasjon av motorenhet Moottorikoneikon asennusohjeet Installeringsvejledning til motorenheden µ Instrukcje instalacji zespolu silnika Tájékoztató a motor beszereléséhez Návod k instalaci motorového agregátu Notice: We guarantee perfect functioning of the product if the following conditions of use are respected: suction pipe: from 3 to 10 m; functioning temperature: from ­ 30°C to +60°. Varning: Produktens perfekta funktion garanteras om följande användningsförhållanden respekteras: utsugningsledning: från 3 till 10 m; brukstemperatur: från ­30°C till +60°C. -- Find the connection box B for the external motor which is located on the top part of the hood assembly. [. . . ]