User manual SMEG KT80EB

[. . . ] DO NOT INSERT DISHES WITH RESIDUES OF ASH, WAX OR VARNISH. NEVER USE THE DISHWASHER OR ITS PARTS AS A STEP-LADDER, SUPPORT OR BRACE FOR PERSONS, THINGS OR ANIMALS. LEANING OR SITTING UPON THE DISHWASHER'S OPEN DOOR COULD CAUSE IT TO TIP, WITH CONSEQUENT PERSONAL DANGER. DO NOT LEAVE THE DISHWASHER'S DOOR OPEN IN ORDER TO AVOID TRIPPING UPON IT. [. . . ] Use only new tubes for the connection to the water supply; old or used tubes must not be utilized. The dynamic supply pressure must be between 2 and 4 bar; if the pressure is higher, a pressure reducer must be installed. It is indispensable to install a general faucet on the supply water input tubing; the faucet must be accessible after installation has been completed. Do not install the faucet behind the dishwasher. The declared cycle durations refer to a 50° hot water supply. Where a cold water supply is used, the duration of the cycle could increase in relation to the input water temperature since the dishwasher is equipped with a constant temperature and pressure rinse system. Drain: Every dishwasher comes equipped with a drain connection tube; this is prescribed to be at floor level, with a trap drain. Caution: make sure that the supply and drain tubes are not bent, restricted or crushed after installation. 6 4. 1 Electrical connection The dishwasher's electrical connection and that of eventual supplementary apparatus is to be entrusted to authorized and qualified personnel, with respect to the norms in vigor; observe also the technical regulations for the connections. The total power installed is given upon the apparatus' technical data label. Other apparatus must not be protected along with the dishwasher. The user must provide for the installation, according to the norms in vigor, of a main electrical power switch and of a differential switch compatible with the machine's characteristics. At the end of the draining phase the CPU still detects water in the Tank. To start the cycle, open the hood, insert the basket and close the hood; the selected led indicator will begin to flash and will stop flashing at the end of the completed cycle. The display will indicate the wash or rinse temperatures based upon the active function of the machine. Note: if the machine came equipped with rinse delay, the wash will continue until the programmed rinse temperature is reached, after which the cycle will terminate. After having selected the continuous cycle indicator will start to flash. To interrupt the cycle press becomes a steady green. The rinse will begin and the cycle will terminate once the led indicator When finished, for models with a drain pump, remove the overflow and press for 4 seconds. Drainage will begin once the led indicator turns on, and will terminate with the automatic shutdown of the machine. 9 PROGRAM SELECTION PROGRAM Glasses Glasses, cups, very dirty plates WASH TYPEOLOGY DURATION (*) Brief about 1' 15" Medium about 2' 10 Silverware and very dirty plates Particularly dirty dishes Long about 3' Continuous from 0 to 10' (*)The cycle durations indicated above are based upon a tri-phase connection with a 50°C hot water supply. Where a cold water supply is used, the duration of the cycle could increase in relation to the input water temperature since the dishwasher is equipped with a constant temperature and pressure rinse system. DISH LOADING Plates The basket can contain 12 bowls or 18 flat plates. Remove solid residues from the dishes (bones, peels, cores, etc. ); before washing, let dishes with residues of dried-on cheese, egg. . . . . . soak in cold water. Glasses Cups should be positioned upside down. Silverware Use the appropriate basket(s). [. . . ] Rinse and dry with care. 10. 3 Prolonged disuse If the use of the dishwasher is not foreseen for a relatively long period of time it is necessary to drain the detergent and rinse-aid dispenser in order to avoid crystallization and pump damage: Remove the suction tubes from the detergent and rinse-aid containers and emerge them in a container filled with clean water. Perform a few wash cycles and drain the machine completely. 12 Finally, turn off the main switch and close the water supply faucet. The detergent and rinse-aid suction tubes will be placed back in the containers when the machine is ready to be put back in use, taking care so as not to invert the tubes (red tube = detergent; transparent tube = rinse-aid). Do not leave the device on, inactive and in disuse for long periods of time. 11 PROBLEMS AND ANOMALIES (USER) PROBLEM THE LED POWER INDICATOR DOES NOT TURN ON POSSIBLE CAUSE There is no electrical current POSSIBLE REMEDY Verify the electrical current connection. [. . . ]