User manual SMEG LBW109E

[. . . ] FULLY AUTOMATIC ELECTRONIC WASHING MACHINE USER MANUAL BEFORE USING THE WASHING MACHINE, YOU SHOULD CERTAINLY READ THE INFORMATION IN USER’S MANUAL. CONTENTS CHAPTER-1: TECHNICAL SPECIFICATIONS 3 5 CHAPTER-2: BEFORE USING WASHING MACHINE Safety warnings 5 Recommendations 6 7 CHAPTER-3: SETTING UP . . . . . Removing transport safety screws 7 Adjusting feet for balance 9 Electrical connection 10 Water inlet connection 10 Water discharge connection 11 CHAPTER-4: PRELIMINARY PREPARATION FOR 12 LAUNDERING 16 CHAPTER-5: CONTROL PANEL Detergent drawer 17 Programme knob 18 Electronic display 19 20 CHAPTER-6: OPERATING YOUR MACHINE Selecting programme 20 Auxiliary functions 20 Starting the programme 29 Adding/Removing laundry 30 Child lock 31 Cancelling programme 32 Finishing programme 33 CHAPTER-7: ELECTRONIC DISPLAY WARNING SYMBOLS 34 Warning of water cut-off/low mains water pressure 34 Warning of clogged pump fitler 35 CHAPTER-8: MAINTENANCE AND CLEANING OF YOUR MACHINE 36 41 CHAPTER-9: PRACTICAL INFORMATION CHAPTER-10: TROUBLESHOOTING 43 CHAPTER-11: AUTOMATIC FAULT WARNINGS AND HOW TO CORRECT THEM 48 50 CHAPTER-12: DESCRIBING AND SAVING ENERGY 2 CHAPTER -1: TECHNICAL SPECIFICATIONS 2 3 4 1 1. Detergent drawer 2. Upper tray 3. Programme knob 4. Electronic display 5. Door 6. Cover of pump filter 5 6 8 9 10 7 7 7. Transport safety screw 8. Power cable 9. Discharging hose 10. Water inlet valve 7 7 3 CHAPTER -1: TECHNICAL SPECIFICATIONS Operating voltage / frequency (V/Hz) Total current (A) Water pressure (Mpa) Total power (W) Maximum dry laundry capacity (kg) Spinning revolution (rev / min) Programme number Dimensions (Height x Width x Depth) (mm) (220-240) V ~/50Hz 10 Maximum: 1 Mpa Minimum: 0. 1 MPa 2200 9 1000 15 845 x 597 x 582 4 CHAPTER -2: BEFORE USING YOUR WASHING MACHINE SAFETY WARNINGS Do not use a multiple socket or extension cord. Do not insert a plug with damaged or broken cord into the socket. If the cord is damaged it should be replaced by the manufacturer or appointed service agent in order to avoid a hazard. [. . . ] When using this function, you should put detergent in front washing compartment of the detergent drawer. 26 CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 4-Auxiliary function for rapid wash This auxiliary function will enable the washing duration of your Laundry that are not very dirty to be shortened. In case you put half of or less than half of the laundry capacity of the washing programme you have selected in your machine, your machine will detect this event thanks to automatic Half-load detection system, and the programme you have selected will wash your Laundry in a shorter time to consume less energy and water. If your machine detects half load, symbol will automatically flash on electronic display. To cancel it, pressing on the auxiliary function of quick washing for once will be enough. However, selection of auxiliary function of quick washing is not possible in course of the same washing operation. 5-Auxiliary function for easy ironing This auxiliary function will use a lower spin speed, resulting in less wrinkled laundry. 27 CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 6-Auxiliary function for delay timer By using this auxiliary function, you can let your machine start washing after half an hour to 23 hours. To use auxiliary function of delay timer: - Press time delay button once. - Expression of “0. 5h” will appear on the display. - Press on time delay button until the time, on which you want washing operation to be started. - To activate the time delay you have selected in the programme, you may press on any auxiliary function button you like except “Start/Pause” button. Intervals of delay timer is half an hour for the first 2 hours, 1 hour for 3 hours to 23 hours. If you have accidentally skipped the time delay you want to set by pushing the time delay timer button more than needed, keep pressing on delay timer button until you set the correct time delay. If you want to cancel the delay timer, you are required to press the delay timer button once. If you want to cancel the delay timer, you are required to press the delay timer button once. To run delay timer function, your machine is required to be operated by pressing on Start/Pause button. As soon as you start your machine, the count down process will start on the electronic display based on the delay period you have selected. 28 CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 7-Anti-Allergic auxiliary function In the programmes where this auxiliary function is active, your machine will perform an extra rinsing operation on your Laundry prior to latest rinsing operation. Note: Anti-Allergic auxiliary function is selected automatically only in Baby wear programme. 29 CHAPTER 6: OPERATING YOUR MACHINE STARTING THE PROGRAMME Start/Pause button By pressing on Start/Pause button, you may start the programme you have selected, suspend a running programme. If you switch your machine to pause mode, electronic display will blink. When you start your machine, the following symbols for the programmes you have selected will be available on electronic display. - Temperature of washing water - Revolution speed - If you have selected, symbols of auxiliary functions - Programme ending time or programme delay time based on your selection - Symbol of open or locked door Note: The flashing symbol for Open Door will come on. This will be replaced by the Locked Door symbol, within a minute of pressing Start /Pause button again. Open door Locked door 30 CHAPTER 6: OPERATING YOUR MACHINE ADDING/REMOVING LAUNDRY Laundry adding to / removing from the machine -If you want to add or remove Laundry when your machine is running, switch your machine to Pause mode by pressing Start/Pause button. - When you Pause the machine, the Open Door symbol will flash and you can open the door to either add or remove laundry. - When you want to unload your machine at the end of a programme the Door Unlocked symbol will flash and you can safely open the door to remove laundry. Note: If symbol blinks on the electronic display, it means that your machine cannot carry out the operation of laundry adding or removing as your machine has passed the steps in question. - Upon completion of laundry adding or removing function, close the door of your machine and press on Start/Pause button. [. . . ] (**) See the section concerning installations your machine. 47 CHAPTER -10: TROUBLESHOOTING PROBABLE CAUSE METHODS OF ELIMINATION The load control system will automatically attempt to balance the load before a spin cycle starts. It is important when loading the machine to distribute laundry evenly, so that the drum load is balanced for spinning. FAILURE The spinning process is not done or starts with delay . No failure. The unbalanced load control works in that way. 48 CHAPTER -11: AUTOMATIC FAULT WARNINGS AND HOW TO CORRECT THEM Your machine is equipped with the systems which are capable of both taking necessary precautions and warning you in case of any breakdown by means of continuous self-checking during washing operations. TROUBLE CODE POSSIBLE FAULT The door of your machine is left open. [. . . ]