User manual SMEG LBW129E

[. . . ] WASHING MACHINE USER’S MANUAL BEFORE USING THE WASHING MACHINE, YOU SHOULD CERTAINLY READ THE INFORMATION IN USER’S MANUAL. CONTENTS CHAPTER-1: TECHNICAL SPECIFICATIONS CHAPTER-2: BEFORE USING WASHING MACHINE Safety warnings Recommendations CHAPTER-3: SETTING UP . . . . . Removing transport safety screws Adjusting adjustable stays Electrical connection Water inlet connection Water discharge connection CHAPTER-4: PRELIMINARY PREPARATION FOR LAUNDERING CHAPTER-5: CONTROL PANEL Detergent drawer Programme knob Electronic display CHAPTER-6: OPERATING YOUR MACHINE Selecting programme Auxiliary functions Starting the programme Adding/Removing laundry Child lock Cancelling programme Finishing programme CHAPTER-7: ELECTRONIC DISPLAY WARNING SYMBOLS Warning of water cut-off/low mains water pressure Warning of clogged pump fitler CHAPTER-8: MAINTENANCE AND CLEANING OF YOUR MACHINE CHAPTER-9: PRACTICAL INFORMATION CHAPTER-10: TROUBLESHOOTING CHAPTER-11: AUTOMATIC FAULT WARNINGS AND WHAT TO BE DONE CHAPTER-12: DESCRIBING AND SAVING ENERGY 3 5 5 6 7 7 9 10 10 11 12 16 17 18 19 20 20 20 29 30 31 32 33 34 34 35 36 41 43 48 50 2 CHAPTER -1: TECHNICAL SPECIFICATIONS 2 3 4 1 1. Detergent drawer 2. Upper tray 3. Programme knob 4. Electronic display 5. Door 6. Cover of pump filter 5 6 8 9 10 7 7 7. Transport safety screw 8. Power cable 9. Discharging hose 10. Water inlet valve 7 7 3 CHAPTER -1: TECHNICAL SPECIFICATIONS Operating voltage / frequency (V/Hz) Total current (A) Water pressure (Mpa) Total power (W) Maximum dry laundry capacity (kg) Wringing revolution (rev / min) Programme number Dimensions (Height x Width x Depth) (mm) (220-240) V ~/50Hz 10 Maximum: 1 Mpa Minimum: 0. 1 MPa 2200 9 1200 15 845 x 597 x 582 4 CHAPTER -2: BEFORE USING YOUR WASHING MACHINE SAFETY WARNINGS SAFETY WARNINGS Do not use multiple receptacles or extension cord. In case of a breakdown of power cable, contact the nearest authorized service for replacing it. Do not plug-in or out the plug from the receptacle with wet hands to prevent electric shock. [. . . ] If you want to cancel the delay timer, you are required to press the delay timer button once. To run delay timer function, your machine is required to be operated by pressing on Start/Pause button. As soon as you start your machine, the count down process will start on the electronic display based on the delay period you have selected. 27 CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 7-Anti-Allergic auxiliary function In the programmes where this auxiliary function is active, your machine will perform an extra rinsing operation on your laundries prior to latest rinsing operation. Note: Anti-Allergic auxiliary function is selected automatically only in Hygiene programme. 28 CHAPTER 6: OPERATING YOUR MACHINE STARTING THE PROGRAMME Start/Pause button By pressing on Start/Pause button, you may start the programme you have selected, suspend a running programme. If you switch your machine to pause mode, electronic display will blink. When you start your machine, the following symbols for the programmes you have selected will be available on electronic display. - Temperature of washing water - Revolution speed - If you have selected, symbols of auxiliary functions - Programme ending time or programme delay time based on your selection - Symbol of open or locked door Note: Symbol for open door flashing on electronic display will go off and symbol for locked door will flash approximately 1 minute after you start your machine by pressing Start/pause button. Open door Locked door 29 CHAPTER 6: OPERATING YOUR MACHINE ADDING/REMOVING LAUNDRY Laundry adding to / removing from the machine If you want to add or remove laundries when your machine is running: - Switch your machine to pause mode by pressing on Start/Pause button. moves over electronic - After a while, if you realize that symbol display, this means that the door of your machine will be convenient for opening. When you see symbol on electronic display, you can either add or remove laundries after opening the machine door. blinks on the electronic display, it means that your Note: If symbol machine cannot carry out the operation of laundry adding or removing as your machine has passed the steps in question. - Upon completion of laundry adding or removing function, close the door of your machine and press on Start/Pause button. - Your machine will continue to wash after locking the door of your machine. - Symbol will flash on electronic display. 30 CHAPTER 6: OPERATING YOUR MACHINE CHILD LOCK Child lock To avoid programme flow from being affected if programme knobs are pressed or programme knob is turned when performing washing operation in your machine, child lock is available. Child lock will be activated in case pressed on both auxiliary functions of quick washing and easy ironing removing at the same time in excess of 3 seconds. Symbol will flash on the electronic display when activated. will blink If pressed any button while child lock is active, symbol on the electronic display. When any of the programmes is running and child lock is active, if another programme is selected after programme knob is switched to 0 position, the programme already running will resume. To deactivate it, it will be sufficient to press on the same buttons for more than 3 seconds. When child lock is deactivated, symbol the electronic display will go off. on 31 CHAPTER 6: OPERATING YOUR MACHINE CANCELLING PROGRAMME Cancelling programme If you want to cancel any programme running: - Switch the programme knob to 0. - Your machine will stop the washing operation and the programme will be cancelled. - To get rid of the water accumulated in the machine switch the programme knob to any programme. - Your machine will perform the necessary discharge operation and cancel the programme. - You can run your machine by selecting a new programme. 32 CHAPTER 6: OPERATING YOUR MACHINE FINISHING PROGRAMME Finishing programme - Your machine will stop by itself as soon as the programme you have selected finishes. -Expression of “END” will flash on the electronic display. Note: Within 2 minutes after the programme has finished, your machine will extinguish the electronic display to save energy. [. . . ] (**) See the chapter regarding installation of your machine. 46 CHAPTER -10: TROUBLESHOOTING FAULT POSSIBLE CAUSE REMOVING METHODS Unbalanced load control system will try to spread your laundries homogeneously. Wringing operation will start after spreading your laundries. Put your laundries in the machine homogeneously in the next washing operation. Wringing operation is not performed or runs late. No fault. Unbalanced load control system has been activated. 47 CHAPTER -11: AUTOMATIC FAULT WARNINGS AND WHAT TO BE DONE Your machine is equipped with the systems which are capable of both taking necessary precautions and warning you in case of any breakdown by means of continuous self-checking during washing operations. [. . . ]