User manual SMEG LBW148E

[. . . ] FULLY AUTOMATIC ELECTRONIC WASHING MACHINE USER MANUAL BEFORE USING THE WASHING MACHINE, YOU SHOULD CERTAINLY READ THE INFORMATION IN USER’S MANUAL. CONTENTS CHAPTER-1: TECHNICAL SPECIFICATIONS 3 5 CHAPTER-2: BEFORE USING WASHING MACHINE Safety warnings 5 Recommendations 6 7 CHAPTER-3: SETTING UP . . . . . Removing transport safety screws 7 Adjusting feet for balance 9 Electrical connection 10 Water inlet connection 10 Water discharge connection 11 CHAPTER-4: PRELIMINARY PREPARATION FOR 12 LAUNDERING 16 CHAPTER-5: CONTROL PANEL Detergent drawer 17 Programme knob 18 Electronic display 19 20 CHAPTER-6: OPERATING YOUR MACHINE Selecting programme 20 Auxiliary functions 20 Starting the programme 29 Adding/Removing laundry 30 Child lock 31 Cancelling programme 32 Finishing programme 33 CHAPTER-7: ELECTRONIC DISPLAY WARNING SYMBOLS 34 Warning of water cut-off/low mains water pressure 34 Warning of clogged pump fitler 35 CHAPTER-8: MAINTENANCE AND CLEANING OF YOUR MACHINE 36 41 CHAPTER-9: PRACTICAL INFORMATION CHAPTER-10: TROUBLESHOOTING 43 CHAPTER-11: AUTOMATIC FAULT WARNINGS AND HOW TO CORRECT THEM 48 50 CHAPTER-12: DESCRIBING AND SAVING ENERGY 2 CHAPTER -1: TECHNICAL SPECIFICATIONS 2 3 4 1 1. Detergent drawer 2. Upper tray 3. Programme knob 4. Electronic display 5. Door 6. Cover of pump filter 5 6 8 9 10 7 7 7. Transport safety screw 8. Power cable 9. Discharging hose 10. Water inlet valve 7 7 3 CHAPTER -1: TECHNICAL SPECIFICATIONS LBW148E Operating voltage / frequency (V/Hz) Total current (A) Water pressure (Mpa) Total power (W) Maximum dry laundry capacity (kg) Spinning revolution (rev / min) Programme number Dimensions (Height x Width x Depth) (mm) (220-240) V ~/50Hz 10 Maximum: 1 Mpa Minimum: 0. 1 MPa 2200 8 1400 15 845 x 597 x 557 4 CHAPTER -2: BEFORE USING YOUR WASHING MACHINE SAFETY WARNINGS Do not use a multiple socket or extension cord. Do not insert a plug with damaged or broken cord into the socket. If the cord is damaged it should be replaced by the manufacturer or appointed service agent in order to avoid a hazard. [. . . ] Intervals of delay timer is half an hour for the first 2 hours, 1 hour for 3 hours to 23 hours. If you have accidentally skipped the time delay you want to set by pushing the time delay timer button more than needed, keep pressing on delay timer button until you set the correct time delay. If you want to cancel the delay timer, you are required to press the delay timer button once. If you want to cancel the delay timer, you are required to press the delay timer button once. To run delay timer function, your machine is required to be operated by pressing on Start/Pause button. As soon as you start your machine, the count down process will start on the electronic display based on the delay period you have selected. 28 CHAPTER 6: OPERATING YOUR MACHINE AUXILIARY FUNCTIONS 7-Anti-Allergic auxiliary function In the programmes where this auxiliary function is active, your machine will perform an extra rinsing operation on your Laundry prior to latest rinsing operation. Note: Anti-Allergic auxiliary function is selected automatically only in Baby wear programme. 29 CHAPTER 6: OPERATING YOUR MACHINE STARTING THE PROGRAMME Start/Pause button By pressing on Start/Pause button, you may start the programme you have selected, suspend a running programme. If you switch your machine to pause mode, electronic display will blink. When you start your machine, the following symbols for the programmes you have selected will be available on electronic display. - Temperature of washing water - Revolution speed - If you have selected, symbols of auxiliary functions - Programme ending time or programme delay time based on your selection - Symbol of open or locked door Note: The flashing symbol for Open Door will come on. This will be replaced by the Locked Door symbol, within a minute of pressing Start /Pause button again. Open door Locked door 30 CHAPTER 6: OPERATING YOUR MACHINE ADDING/REMOVING LAUNDRY Laundry adding to / removing from the machine -If you want to add or remove Laundry when your machine is running, switch your machine to Pause mode by pressing Start/Pause button. - When you Pause the machine, the Open Door symbol will flash and you can open the door to either add or remove laundry. - When you want to unload your machine at the end of a programme the Door Unlocked symbol will flash and you can safely open the door to remove laundry. Note: If symbol blinks on the electronic display, it means that your machine cannot carry out the operation of laundry adding or removing as your machine has passed the steps in question. - Upon completion of laundry adding or removing function, close the door of your machine and press on Start/Pause button. - Your machine will continue to wash after locking the door of your machine. - Symbol will flash on electronic display. 31 CHAPTER 6: OPERATING YOUR MACHINE CHILD LOCK Child lock To avoid the cycle being altered if any programme knobs are pressed or turned when a programme has started, the Child Lock may be set. Child lock is an auxiliary function which can be activated by pressing and holding Quick Wash and Wrinkle Removing functions together for 3 seconds. Symbol will flash on the electronic display when activated. will blink If any button is pressed while child lock is active, symbol on the electronic display. When any of the programmes is running and child lock is active, if another programme is selected after programme knob is switched to 0 position, the programme already running will resume. To deactivate it, it will be sufficient to press on the same buttons for more than 3 seconds. When child lock is deactivated, symbol the electronic display will go off. on 32 CHAPTER 6: OPERATING YOUR MACHINE CANCELLING PROGRAMME Cancelling programme If you want to cancel any programme running: - Switch the programme knob to 0. - Your machine will stop the washing operation and the programme will be cancelled. [. . . ] (**) See the section concerning installations your machine. 47 CHAPTER -10: TROUBLESHOOTING PROBABLE CAUSE METHODS OF ELIMINATION The load control system will automatically attempt to balance the load before a spin cycle starts. It is important when loading the machine to distribute laundry evenly, so that the drum load is balanced for spinning. FAILURE The spinning process is not done or starts with delay . No failure. The unbalanced load control works in that way. 48 CHAPTER -11: AUTOMATIC FAULT WARNINGS AND HOW TO CORRECT THEM Your machine is equipped with the systems which are capable of both taking necessary precautions and warning you in case of any breakdown by means of continuous self-checking during washing operations. TROUBLE CODE POSSIBLE FAULT The door of your machine is left open. [. . . ]