User manual SMEG LS52XA

[. . . ] Operating instructions ____________________________________ 38 4. 1 4. 2 4. 3 4. 4 Using the water softening system ______________________________________________ 38 Using the rinse aid and detergent dispensers _____________________________________ 40 General warnings and recommendations ________________________________________ 42 Using the baskets___________________________________________________________ 43 5. Cleaning and maintenance ________________________________ 46 5. 1 General warnings and recommendations ________________________________________ 46 6. Troubleshooting ________________________________________ 49 Thank you for choosing this product. We advise you to carefully read all the instructions contained in this manual, in order to understand how to operate your dishwasher safely and correctly. [. . . ] To avoid using excessive amounts of detergent and to save on electricity, observe the following: · separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures; · do not pour the detergent directly on the dishes. 36 User instructions STARTING THE DISHWASHER After correctly carrying out all the preceding operations, to start the dishwasher simply press the START/STOP (5) button for a few seconds, until the start cycle acoustic device sounds. The INFORMATION DISPLAY (8) will show the duration of the program in minutes. The duration time is only approximate, because it depends on the washing conditions (quantity of dishes, water temperature, etc. ), and is also continually updated as the washing program progresses. The INFORMATION DISPLAY (8) shows the estimated duration of the washing program; if it exceeds 60 minutes, the hours and minutes are displayed in alternation. If it is necessary to open dishwasher door during the washing cycle, there will be a 1-minute delay before the program can be resumed. After correctly closing the door, press the START/STOP (5) button again. This operation may negatively affective the progress of the washing cycle. END OF CYCLE The end of the washing cycle is signalled by a brief sounding of an acoustic device and by the blinking of the selected program on the INFORMATION DISPLAY (8). Before setting a new washing program, the door must first be opened, then reclosed, or the START/STOP (5) button pressed to "reset" the display and stop the flashing. REMOVING THE DISHES At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket. 37 User instructions 4. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: · Adjust the water softening system; · Add the regenerating salt; · Add the rinse aid and detergent. 4. 1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness 41-60°dF ­ 24-31°dH). SALT When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. Replace the cover and turn it in a clockwise direction. Use a cloth to remove any spillage of rinse aid which might lead to the formation of excess foam. ADJUSTING THE RINSE AID DISPENSER SETTING The dishwasher is factory set for medium water hardness. However it possible to change the setting by turning the dispenser's selector to the desired position: the amount of rinse aid dispensed is proportional to the selector position. The setting must be increased when the washed dishes appear dull or have circular staining. · · · · · To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it. Then use a screwdriver to rotate the rinse aid selector to the desired position. The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains. If, on the other hand, the dishes are sticky or have white streaks, it is necessary to reduce the rinse aid setting. 40 User instructions ADDING THE DETERGENT To open the detergent dispenser cap, lightly press the button P. Add the detergent and close the cap carefully. During the washing cycle, the dispenser will be opened automatically. · When a SUPER program is selected, in addition to the normal dose of detergent, it is necessary to add an additional amount inside compartment G or H. Use only detergents specially formulated for dishwashers. For optimal washing results it is important to use a good quality detergent. [. . . ] It is essential to thoroughly clean the filters according to the above instructions: the dishwasher cannot function if the filters are clogged. Carefully replace the filters in their seats, to avoid damaging the wash pump. PROLONGED DISUSE: · · · · · Run the soak program twice in succession. Leave the door slightly open, in order to prevent the formation of unpleasant odours inside the washing tank. Shut off the water supply tap. BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE: · · · Check that there are no deposits of sludge or rust inside the water pipe: if there are, allow the water to run from the water supply tap for a few minutes. [. . . ]