User manual SMEG LSE16

[. . . ] The user is thus obliged to consign scrapped appliances to the special electronic and electrotechnical waste disposal centres, or return them to the dealer on purchase of a similar new appliance, on a one-to-one basis. Consignment to the appropriate facility for environmentally responsible recycling, treatment and disposal helps to prevent any negative effects on the environment and health, and encourages the reuse and/or recycling of the appliance's component materials. Illegal dumping of the appliance by the user will be subject to prosecution under the relevant law. 1 EN READ THE INSTRUCTIONS Attention!You are advised to read all the instructions in this manual carefully; it will inform you about the right conditions for the proper, safe use of your washing machine. [. . . ] · Failure to comply with washing guidance symbols may result in damage to the items washed. Wool ­ Only wool marked as pure new wool, with the mark, or labelled "shrink-proof, machine-washable" can be washed in a washing machine on the specific programme; other types of wool should be hand-washed or dry-cleaned. 4. 2 OPENING THE DOOR The appliance is fitted with a safety device which prevents the door from being opened while the programme is in progress. Check that all the water has been drained from the tank and the drum is at a standstill. · If the washing programme is interrupted, it will be from 3 to 15 minutes before the door can be opened, depending on the temperature reached inside the appliance. The water may still be boiling hot if the wash was at high temperature. Do not open the door if there is still water in the drum! 4. 3 LOADS OF WASHING As far as possible, to save electricity, it is more economical to wash complete loads of the various types of fabric. Shake out the washing before loading, and alternate large and small items. It is best to weight the load the first few times, after which you will be able to rely on your experience. As a guide, the following is a list of the average weights of the standard items: 9 EN 4. 4 LOADING THE ITEMS FOR WASHING 1. Open the door and load the washing, distributing it evenly over the drum, with items opened out and not bundled together; if possible, large and small items should be well mixed. The washing machine covered by this manual can be loaded with up to 7kg of washing for each wash. · Use the doses recommended by the detergent producer. 4. 7 LIQUID DETERGENT DOSES 1. Pour the dose required into the measuring cap supplied with the bottle of liquid detergent and place it in the drum, or use the main wash compartment of the detergent drawer, fitting the insert provided. The scale on the red insert is intended as an aid when deciding the dose of liquid detergent. Warning!· Liquid detergents can be used, at the doses recommended by the producer, only for the main wash, i. e. in all programmes without prewash. 4. 8 DESCALERS Descalers can be added to the prewash and main wash compartments as recommended by their producers. Place the detergent in the compartments first, followed by the descaler. 4. 9 PROGRAMMES AND FUNCTIONS For advice on selecting programmes in relation to the type of fabric, refer to the "Programmes Table", supplied with this manual. 11 EN 4. 10 SWITCHING ON THE APPLIANCE AND SELECTING THE WASHING PROGRAMME To switch on the appliance and select the programme, proceed as follows: 1. Turn the programmes knob in either direction. The time left to the end of the programme on the display. The symbols on the display light up to identify the information shown. The default spin speed values are shown. The initial settings can be modified using the button underneath the sequence of spin speeds. [. . . ] Using the template 1) Measure the height of the kitchen baseboard: the height of the wooden panel is obtained by first establishing the height of the kitchen baseboard. E. g. : for a 100 mm high baseboard, the maximum height of the panel is 720 mm. If the height of the baseboard must be increased, the height of the wooden panel must be reduced. Applying the panel 4 Place the template of the inner side of the panel and match the height of the baseboard with the lower edge of the panel (fig. Make sure the template is horizontally centred with reference to the vertical lines marked at the ends. [. . . ]