User manual SMEG P663-1

[. . . ] 9. INSTRUCTIONS FOR PROPER USE ______________________________________ 19 SAFETY INSTRUCTION ________________________________________________ 20 KNOW YOUR HOB ____________________________________________________ 21 BEFORE FIRST USE___________________________________________________ 21 COOKING ZONES_____________________________________________________ 22 DESCRIPTION OF CONTROL ON THE FRONT CONTROL PANEL______________ 23 USE OF THE COOKING HOB____________________________________________ 24 CLEANING AND MAINTENANCE _________________________________________ 28 SOMETHING WRONG?________________________________________________ 28 10. INSTALLATION _______________________________________________________ 29 INSTRUCTIONS FOR THE USER: these contain user advice, description of the commands and the correct procedures for cleaning and maintenance of the appliance. INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must install the appliance, set it functioning and carry out an inspection test. @ 18 Further information about the products can be found at www. smeg. com Instructions for proper use 1. [. . . ] press the (0 appears on the display: meaning that the plate has been switched on); 2. press the (9 appears on the display: meaning that the plate is on at full power); 3. Pressing the symbol repeatedly regulates the plate's power setting from the full power level (9) towards the lowest setting (1); b. Pressing the symbol repeatedly regulates the plate's power setting from the lowest power level (1) to the highest setting (9); 4. To switch off the plate, return the display reading to 0 by pressing the or symbol repeatedly. A "BEEP" of confirmation is heard whenever the or symbols are pressed. 7. 2. 2 Dual plates Operation of plates with dual heating is different from that of those with single heating. When they are switched on, two indicator lights illuminate beside the number showing the power level, as shown in the diagram. When not in use, all hob components will be switched off. If the symbol of any push-button is pressed for a few seconds, the hob will switch on and the circular sectors on the buttons indicating the plate controlled by each button will illuminate. The power level must be set within 30 seconds after the sectors light up; otherwise the hob will switch off automatically. To set the power level use the or push-buttons as follows: 1. press the symbol (0 appears on the display, meaning that the plate is on at full power); 2. press the symbol again (9 appears on the display, meaning that the small plate is on at full power); 3. · press the symbol once (two markers illuminate beside the 9); · press the symbol to set the power of the dual plate. · after proceeding as described in point 2, press the the symbol repeatedly to set the power of the small plate; 4. To switch off the plate, return the display reading to 0 by pressing the symbol repeatedly. 25 Instructions for the user 7. 2. 3 Plate lock-out 20 seconds after the last power adjustment, the plate switches to "lock-out" status and no more adjustments to the power levels set will be possible. This function, indicated by a dot which appears alongside the power level (see side), is provided to ensure greater safety in use of the hob. The "lock-out" can be eliminated by keeping the or symbol of any push-button pressed for 2-3 second. 7. 2. 4 Plate layout REAR LEFT FRONT LEFT REAR RIGHT FRONT RIGHT MIDDLE 7. 2. 5 Timer (on some models only) Some models are equipped with cooking timer. To activate the timer, proceed as follows: with the plates on or off; 1. keep the symbol pressed for a few seconds (the two displays in the middle of the screenprinting will switch on, showing a flashing figure 30) (if the plate is on, the power display value will drop by one point, but it will return to the previous value at once); 2. [. . . ] If the appliance you have purchased is not fitted with a mains power lead a power lead resistant to a temperature of at least 90°C must be used. Otherwise, the electrical safety of the appliance may be put at risk. The manufacturer declines all responsibility for damage to persons or things caused by nonobservance of the above prescriptions or by interference with any part of the appliance. Warning: pass the power cable through hole "A" and fit the cable clamp plate after making the electrical connection. [. . . ]