User manual SMEG P755SBBN

[. . . ] INSTRUCTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ENVIRONMENTAL RESPONSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DESCRIPTION OF CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To turn off the burner, turn the knob to the zero position to the symbol. 9 Instructions for the user 5. USING THE HOB Make sure that the burners, flame-spreader crowns and racks are fitted correctly. The notches A of the flame-spreader crowns must be inserted into the housings B of the burner. The igniter and thermocouple on the hob should fit into the 2 holes on the burner. 5. 1 Positioning the racks The racks are provided unassembled on the hob. To position each rack correctly on its burner, follow the instructions below: Each rack must be positioned on the corresponding burner in order to guarantee proper operation. Be very careful to match the different central diameters of the racks to the flame-spreader crowns. 10 Instructions for the user All the racks have two reference notches (A). To position the racks correctly, align the reference notches (A) with the cavities (B) on the hob. After positioning, check that the rack feet are all resting on the same level. Make sure that the racks are simply centred on their respective burners, without forcing the burners to be raised or tilted. If they are, repeat the positioning procedure. INCORRECT INCORRECT CORRECT 11 Instructions for the user 5. 2 Lighting the burners using a safety device , until it The appliance is equipped with electronic ignition. Simply press the knob and simultaneously turn it anticlockwise to the minimum flame symbol lights. Hold down the knob for about 2 seconds to keep the flame lit and to activate the safety device. The burner may go out when the knob is released. If this happens, repeat the procedure, holding the knob down for longer. If the burners should go out accidentally, after about 20 seconds a safety device will be tripped, cutting off the gas supply, even if the gas tap is open. 5. 3 Practical tips for using the burners For better burner performance and minimum gas consumption, pans with flat, even bases and with lids should be used, and their size should be in proportion to the burner (see "5. 4 Pan diameters"). During cooking, in order to avoid burns or damage to the hob top, all pans or griddles must be positioned inside the outer edge of the hob and at a minimum distance of 5-7 cm must be maintained from the knobs. If the burner flame accidentally goes out, turn off the control knob and wait at least 1 minute before trying to re-light the burner. 12 Instructions for the user 5. 4 Pan diameters BURNERS 1 2. 3 4 Auxiliary Semi-rapid Medium Rapid Large Rapid min. Ø (in cm) 7-18 10-24 18-24 20-26 13 Instructions for the user 6. CLEANING AND MAINTENANCE Before performing any operations requiring access to powered parts, disconnect the appliance from the power supply. 6. 1 Cleaning the hob To keep the hob in good condition it should be cleaned regularly after use. Let it cool first. 6. 1. 1 Ordinary daily cleaning To clean and preserve the stainless steel surfaces, always use only specific products that do not contain abrasives or chlorine-based acids. How to use: pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or chamois leather. [. . . ] 9. 3 Extraction of the combustion products The combustion products may be extracted by means of hoods connected to a natural draught chimney whose efficiency is certain or via forced extraction. An efficient extraction system requires precision planning by a specialist qualified in this area and must comply with the positions and distances indicated by the regulations. When the job is complete, the installer must issue a certificate of conformity. 20 Instructions for the installer 10. ADAPTATION TO DIFFERENT TYPES OF GAS Before carrying out the following operations, disconnect the appliance from the power supply. [. . . ]