User manual SMEG P775PO

[. . . ] INSTRUCTIONS FOR PROPER USE ELECTRICAL CONNECTION: PLEASE REFER TO INSTALLATION INSTRUCTION FOR THE GAS & ELECTRICAL SAFETY REGULATIONS AND THE VENTILATION REQUIREMENTS. IN YOUR OWN INTEREST, AND THAT OF SAFETY, IT IS THE LAW THAT ALL GAS AND ELCTRICAL APPLIANCES BE INSTALLED AND SERVICE BY COMPETENT PERSONS, WHO WILL COMPLY WITH THE RELEVANT STANDARDS AND REGULATIONS. CORGI REGISTERED INSTALLERS UNDERTAKE TO WORK TO SATISFCTIORY STANDARDS. DISCONNECTION OF GAS AND ELECTRIC APPLIANCES SHOULD ALWAYS BE CARRIED OUT BY COMPETENT PERSON. [. . . ] and then To heat both the inner and outer cooking zones, turn the knob to release. To adjust heating intensity, rotate the knob anticlockwise to the desired position. To return to heating of the inner cooking zone only, set the knob back to 0 and then turn to the desired position (1 to 6). 7. 1. 3 Description of symbols REAR LEFT REAR RIGHT FRONT LEFT FRONT RIGHT 7. 1. 4 Residual heat The 4 signal lamps located between the cooking zones come on when the temperature of one or more of the heating zones exceeds 60°C. The lamps go off upon temperature dropping to below approximately 60°C. 7. 1. 5 Switching off To turn off, return the knob to 0. 24 Instructions for the user 7. 2 Hobs with push-buttons On first connection to the electrical mains, an operating check will be carried out automatically and all the indicator lights will come on for a few seconds. 7. 2. 1 Single plates When not in use, all hob components will be switched off. If the symbol of any push-button is pressed for a few seconds, the hob will switch on and the circular sectors on the buttons indicating the plate controlled by each button will illuminate. The power level must be set within 30 seconds after the sectors light up; otherwise the hob will switch off automatically. To set the power level use the or push-buttons as follows: 1. press the (0 appears on the display: meaning that the plate has been switched on); 2. seconds after the last key is pressed, the minutes display will stop flashing and the figure 0 on the power display will start to flash. The power level must be set within another 5 seconds as described in points 7. 2. 1 / 7. 2. 2; otherwise the hob will switch off automatically. If the power is not adjusted within 5 seconds, the timer will still start the count. Timed cooking will start 5 seconds after the last power adjustment. At the end of the time set, 3 BEEPS will sound in sequence; they are repeated 5 times at 5 second intervals. To stop the beeps in manual mode, simply press the or symbol of any push-button. 7. 2. 6 Modifying the data set During timed cooking, each single pressure on the or symbols increases or reduces the power of the plate. 5 seconds after the last button is pressed, a BEEP will sound and the display showing the time left will start flashing. The or symbols can now be pressed to increase or decrease the cooking time. A few seconds after the last cooking time adjustment, the minutes display will also stop flashing and the count will restart with the new settings. 7. 2. 7 Residual heat Each plate is equipped with a residual heat warning device. [. . . ] IF A FIXED CONNECTION IS BEING USED FIT POWER LINE WITH AN OMNIPOLAR CIRCUIT BREAKER WITH A CONTACT OPENING GAP EQUAL TO OR GREATER THAN 3 MM IN AN EASILY ACCESSIBLE POSITION IN PROXIMITY TO THE OVEN. 29 Instructions for the installer For operation on 380-415 V 3N: use a H05RRF / H05RN-F type fivecore cable (5 x 1, 5 mm2). This type of connection cannot be used for models with 5 plates. For operation on 380-415 V 2N: use a H05RR-F / H05RN-F type four-core cable (4 x 2, 5 mm2). For operation on 220-240 V 3: use a H05RR-F / H05RN-F type fourcore cable (4 x 2, 5 mm2). For operation on 220-240 V: use a H05RR-F / H05RN-F type threecore cable. (3 x 2. 5 mm2 : cooking hob with 4 plates) (3 x 4 mm2 : cooking hob with 5 plates) The cable end to be connected to the appliance must be provided with an earth wire (yellow-green) at least 20 mm longer. Read the connection layout plate underneath the appliance with care. [. . . ]