User manual SMEG PGA95-4

[. . . ] INSTRUCTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ENVIRONMENTAL RESPONSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 USING THE HOB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] NEVER USE A STEAM JET FOR CLEANING THE APPLIANCE. 5. 1 Cleaning stainless steel To keep stainless steel in good condition it should be cleaned regularly after use. 5. 1. 1 Ordinary daily cleaning To clean and preserve the stainless steel surfaces, use only specific products that do not contain abrasives or chlorine-based acids. How to use: pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or chamois leather. 5. 1. 2 Food stains or residues Never use metallic sponges or sharp scrapers as they will damage the surface. Use ordinary non-abrasive products for steel, with the aid of wooden or plastic utensils if necessary. Rinse thoroughly and dry with a soft cloth or chamois leather. 5. 2 Cleaning the cooking hob parts For easier cleaning the pan stands, burner caps, flame spreader crowns and burners can all be removed; wash them with warm water and a non-abrasive detergent making sure to remove any encrustation, then wait until they are completely dry. Replace the burner caps on their corresponding crowns, making sure that the slots A are centred with the pins B on the burners. For correct operation, the igniters and thermocouples must always be perfectly clean. Check them frequently and clean them with a damp cloth if necessary. Remove any dry residues with a wooden toothpick or a needle. 12 Instructions for the user In models with central pan stand, fit this piece, taking care that its centre is perfectly aligned with the centre of the burner In models equipped with pan stands, fit as shown in the figure, taking care to position them exactly as shown. Refer to the enlarged details in the figure below for guidance. 13 Instructions for the user 5. 3 Preventive Maintenance This appliance does not need any special maintenance. However, a few simple operations have to be carried out periodically to prevent malfunctioning; Burners: the burners must be cleaned periodically to ensure correct conbustion make sure that all the openings and flame ports are clean and free of obstacles, and the burners rest firmly on their supports. Make sure that there is a minimum of 750 mm between the gas rings and any shelf that may be installed directly above them. 1) (only 60 cm models) Carefully position the supplied insulating seal on the outer edge of the hole on the top hob, as indicated in figure 2. Try and make it stick to the whole surface by applying light hand pressure. The front and back sides of the seal must be touching the hole. Trim any excess trimming from border A with care (Fig. 3). The quotes in figure 2 are references for the hole on the inside of the trimming. The small brackets in figure 4 are only positioned after having mounted the hob. 2) 3) Carry out this operation by supporting the hob on the isolating seal and using screws and clamping brackets (Fig. 4) to fix the hob to the support structure, in order to obtain the complete flatness. 4) 15 Instructions for the installer PGA64 PSA906 PGA75SC3 PGA95SC3 (only "906" models) PGA32 51 0, 8 31 0, 8 3, 3 29 2 73 49 4 16 Instructions for the installer 6. 2 Fixing to the electric model support structure Create an opening with the dimensions shown in the figure in the top surface of the counter, keeping a minimum distance of 50 mm from the rear edge. The lower part of the casing must be fully accessible after the appliance has been installed. This appliance can be mounted against walls higher than the work surface on condition that a distance of "X" be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating. Make sure that there is a minimum of 750 mm between the hob ring flames and any shelves placed directly above them (Fig. [. . . ] The pressure must be checked to ensure it is operating at 2. 75kPa. A separate test point fitting must be installed between the piping & the appliance for the pressure to be checked to ensure it is operating at 2. 75kPa. 23 Instructions for the installer Installation with the flexible hose must be carried out so that the length of the piping does not exceed 2 metres fully extended; make sure that the hoses do not come into contact with moving parts and that they are not crushed in any way. 6. 6 Connection to liquid gas Use a pressure regulator and make the connection on the gas cylinder following the guidelines established by the regulations in force. Make sure that the feed pressure complies with the values indicated in the table at point "9. 2 Burner and nozzle characteristics table". 6. 7 Room ventilation Caution ­ This hob may only be installed and operated in rooms permanently ventilated in accordance with current regulations. [. . . ]