User manual SMEG PGF32G

[. . . ] INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must install the appliance, set it functioning and carry out an inspection test. 23 General instructions 1. INSTRUCTIONS FOR USE THIS MANUAL CONSTITUTES AN INTEGRAL PART OF THE APPLIANCE. THIS MANUAL CONSTITUTES AN INTEGRAL PART OF THE APPLIANCE. IT SHOULD BE KEPT INTACT AND AT HAND FOR THE APPLIANCE'S ENTIRE LIFE CYCLE. [. . . ] Do not discard the packaging or any part of it, or leave it unattended. It can constitute a suffocation hazard for children, especially the plastic bags. Your old appliance also needs to be disposed of correctly. Important: hand over your appliance to the local agency authorised for the collection of electrical appliances no longer in use. Correct disposal enables intelligent recovery of valuable materials. Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use, to ensure that children cannot accidentally become trapped inside during play. It is also necessary to cut the connecting cable to the power grid, removing it along with the plug. 28 Instructions for the user 4. KNOW YOUR APPLIANCE 2 3 1 1 2 3 Auxiliary Burner (AUX) Rapid Burner (R) Dual Crown Burner (UR2) 29 Instructions for the user 5. USING THE HOB 5. 1 Lighting the hob burners Before lighting the hob burners, check that the flame-spreader crowns are correctly in place with their respective burner caps, making sure that the holes A in the flame-spreaders are aligned with the igniters and thermocouples. For dual burner UR2, place and lock caps G and F perfectly on burner D. This latter, in turn, must be placed and locked into the base B (use pins C as a reference). Rack H is for use with woks. F G A C B D H The burner controlled by each knob is shown next to the knob. The appliance is equipped with an electrical ignition device. Simply press the knob and turn it anti-clockwise to the maximum flame symbol , until the burner lights. On valved models, once the burner is lit, keep the knob pressed for a few seconds to give the thermocouple time to heat up. The burner may go out when the knob is released: in this case, the thermocouple has not heated up sufficiently. Wait a few moments and repeat the operation, keeping the knob pressed for longer. This is not necessary on burners that are not equipped with a thermocouple. Once the burner is lit, the flame can be adjusted as required. Always check that the control knobs are in the O (off) position when you finish using the hob. If the burners should go out accidentally, after about 20 seconds a safety device will be tripped, cutting off the gas supply, even if the gas tap is open. 30 Instructions for the user 5. 2 Practical tips for using the burners For better burner efficiency and to minimise gas consumption, use pans with a flat, smooth base and a lid that have a suitable size for the burner, thus preventing the flames reaching the sides of the pan (see point "5. 3 Pan diameters"). Once the contents come to the boil, turn down the flame far enough to prevent the liquid from boiling over. To prevent burns or damage to the hob during cooking, all pans or griddles must be placed inside the perimeter of the hob. [. . . ] Replace the burners in the correct position. The nozzles for using city gas (G110 ­ 8 mbar) are available from authorised service centres. 39 Instructions for the installer 8. 2 Burner and nozzle characteristics table Rated heating capacity (kW) Nozzle diameter 1/100 mm Auxiliary (1) Rapid (2) Dual crown (3) INT Dual crown (3) EXT 1. 05 2. 50 0. 90 3. 60 Rated heating capacity (kW) 50 79 46 68 + 68 Burner Liquid gas - G30/G31 28/37 mbar By-pass mm 1/100 30 42 30 63 Rated capacity (W) 400 800 400 1600 Rated g/h G30 76 182 65 262 Rated g/h G31 75 179 64 257 Burner Natural gas - G20 20 mbar Nozzle diameter 1/100 mm Reduced capacity (W) 400 800 400 1600 I Auxiliary (1) Rapid (2) Dual crown (3) INT Dual crown (3) EXT 1. 05 2. 50 0. 90 3. 60 72 108 70 102 + 102 8. 3 Arrangement of the burners on the cooking hob HOB BURNER 2 3 1 1 2 3 Auxiliary Rapid Dual crown After making the adjustments described above, reassemble the appliance by following the instructions in point "8. 1 Replacement of nozzles on the hob" in reverse order. After adjustment with a gas other than the preset one, replace the label on the bottom of the casing with the label corresponding to the new gas. This label is supplied with the appliance (when applicable) or can be obtained from the nearest Authorised Service Centre. 40 Instructions for the installer 8. 4 Adjusting the minimum for town and natural gas Light the burner and turn it to the minimum position. Extract the gas tap knob and turn the adjustment screw on the left side of the tap (indicated in the figure) until the correct minimum flame is achieved. [. . . ]