User manual SMEG PGF95D-4

[. . . ] SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE. ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION (OFF) WHEN YOU FINISH USING THE HOB. THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. 17 Introduction DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE COOKING HOB GRIDS. DO NOT USE RECIPIENTS OR GRIDDLE PLATES THAT EXTEND BEYOND THE EXTERNAL PERIMETER OF THE HOB. THE HOB IS TO BE USED BY ADULTS ONLY. DO NOT LET UNSUPERVISED CHILDREN PLAY WITH THE HOB. REPLACED APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE COLLECTION CENTRE. The manufacturer declines all responsibility for damage to persons or things caused by non-observance of the above prescriptions or by interference with any part of the appliance or by the use of non-original spares. 18 Instructions for the installer 2. [. . . ] Secure the hob to the counter with brackets A or B(supplied). Carefully trim any excess from border C of the gasket. The distances in the following drawing refer to the hole on the inner side of the gasket. Bracket `A' in the 1st slot Bracket `A' in the 2nd slot 19 Instructions for the installer 2. 2 Fixing the flush-top model to the structure. dimensions shown in the figure in the top surface of the counter, keeping a minimum distance of 50 mm from the rear border. This appliance is classified as "type Y" in relation to fire hazards and can therefore be mounted against walls higher than the work surface on condition that a certain distance "X" be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating. Make sure there is a minimum of 750 mm between the hot plate flames and any shelf that may be installed directly above them. 2 3 This type of appliance also requires a cut 2 mm deep in the worktop of the size shown in figure 3. Before putting the worktop in place, fit the gasket right around the perimeter of the appliance and make sure that it fits snugly against the metal. The gasket must be fitted as shown in figure 5. 4 5 The appliance can also be installed using silicone instead of the gasket supplied. In this case, the installer is responsible for ensuring that the appliance is perfectly level with the top of the unit. 2. 3 Electrical connection Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the current electrical system regulations. Check that the power line is adequately grounded. 20 Instructions for the installer On the power line, install an omnipolar cut-off device with contact cut-off distance greater than or equal to 3 mm, located in an easily accessible position near the unit. In the case of functioning with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps. To change the nozzles, proceed as described below. 3. 1 Replacement of nozzles on the hob This operation requires no primary air regulation. Extract the grids and remove all the caps and flame-spreader crowns; 2. unscrew the burner nozzles with a 7 mm socket wrench; 3. replace the nozzles according to the type of gas to be used and the description in paragraph "3. 2 Burner and nozzle characteristics table". Replace the burners in the correct position. 23 Instructions for the installer 3. 2 Burner and nozzle characteristics table Burner Rated heating capacity (kW) Nozzle diameter 1/100 mm 50 65 75 94 Rated heating capacity (kW) LPG ­ G30/G31 28/37 mbar Auxiliary (1) Semi rapid (2) Rapid (3) Ultrarapid (3) 1. 05 1. 8 2. 3 3. 5 By-pass mm 1/100 30 33 45 65 Reduced flowrate (W) 350 450 800 1. 6 Flowrate g/h G30 76 130 166 253 Flowrate g/h G31 75 128 164 250 Burner Natural gas ­ G20 20 mbar Auxiliary (1) Semi rapid (2) Rapid (3) Ultrarapid (4) 1. 05 1. 8 2. 3 3. 5 Nozzle diameter 1/100 mm 72 97 103 133 Reduced flowrate (W) 350 450 800 1500 3. 3 Arrangement of burners on cooking hob BURNERS 1 2 3 4 Auxiliary Semi rapid Rapid Ultrarapid 24 Instructions for the installer 4. FINAL OPERATIONS Having carried out the above adjustments, reassemble the appliance following, backwards, the instructions in paragraph "3. 2 Burner and nozzle characteristics table". After adjustment to a different kind of gas from the one for which the cooker has been tested, replace the plate inside the heating compartment with one corresponding to the new kind of gas. This plate can be obtained from your nearest Authorised Assistance Centre. 4. 1 Adjustment of minimum for natural gas Light the burner and take it to the minimum. Remove the gas tap knob and turn the adjustment screw inside or at the side of the tap shaft (depending on the model) until there is a regular minimum flame. Replace the knob and check burner flame stability: (rapidly turning the knob from maximum to minimum position, the flame should not go out). [. . . ] To prevent deterioration of the hob we have equipped the cooker with a raised pan stand C to be placed underneath pans more than 26 cm in diameter. The supplied reduction rest C is also used for small pans. Each knob corresponds to the burner indicated. The appliance is equipped with an electric lighting device. To light the burners, press and turn the knob anticlockwise to the large flame symbol . [. . . ]