User manual SMEG PK4210

[. . . ] Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. Do not flamb under the range hood; risk of fire This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. 650 mm min. MAINTENANCE Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. Clean and/or replace the Filters after the specified time period (Fire hazard). [. . . ] Clean the hood using a damp cloth and a neutral liquid detergent. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. EN 1 12 2 CHARACTERISTICS Dimensions max. 890 740 80 259 898 300 150 Min. 650mm 650mm 490 108 Components Ref. 1 2 2. 1 2. 2 9 10 14. 1 15 Q. ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Telescopic Chimney comprising: 1 Upper Section 1 Lower Section 1 Reducer Flange 150-120 mm 1 Damper 2 Air Outlet Connection Extension 1 Air Outlet Connection 260 430 15 14. 1 12a 7. 2. 1 9 10 11 2. 1 2 2. 2 12c Ref. Q. ty Installation Components 7. 2. 1 2 Upper Chimney Section Fixing Brackets 11 6 Wall Plugs 12a 6 Screws 4, 2 x 44, 4 12c 6 Screws 2, 9 x 9, 5 Q. ty Documentation 1 Instruction Manual 1 11 12a EN 1 13 3 INSTALLATION Wall drilling and bracket fixing 12 11 12a 116 116 340 Wall marking: Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. Draw a horizontal line at 650 mm above the hob. Place bracket 7. 2. 1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. Mark the wall at the centres of the holes in the bracket. The comfort panel must never be washed in a dishwasher. Clean the outside by using a damp cloth and neutral liquid detergent. Clean the inside as well by using a damp cloth and neutral detergent; do not use wet cloths or sponges, or jets of water; do not use abrasive substances. When the above operation has been completed, hook the panel back to the hood canopy and close it by turning the knob in the opposite direction. Metal grease filters These can also be washed in the dishwasher, and need to be cleaned when all the command LEDs light up in a continuous manner or at least once every 2 months use, or more frequently if use is particularly intensive. Resetting the alarm signal Press any of the buttons except the Light button. Cleaning the Filters Open the comfort panel. Remove the Filters one at a time, pushing them towards the back of the unit and at the same time pulling downward. Wash the Filters without bending them, and leave them to dry completely before replacing. Replace, taking care to ensure that the handle faces forwards. Close the comfort panel. EN 1 18 8 Activated Charcoal Filter (Recirculation Version) This cannot be washed or regenerated, and must be changed when all the command LEDs start to flash, or at least once every 4 months. Activating the alarm signal In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installation or at a later date. [. . . ] Close the comfort panel. EN 1 18 8 Activated Charcoal Filter (Recirculation Version) This cannot be washed or regenerated, and must be changed when all the command LEDs start to flash, or at least once every 4 months. Activating the alarm signal In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installation or at a later date. Press and hold the Delay button (T4) on the keypad for 5 seconds and the following will be displayed: Leds (L1-L2-L3) flash twice Activated Charcoal Filter saturation alarm ACTIVATED. Leds (L1-L2-L3) flash once Activated Charcoal Filter saturation alarm DEACTI VATED. [. . . ]