User manual SMEG PL19-2

[. . . ] INSTRUCTION MANUAL DISHWASHER Contents 1. Safety and operating instructions __________________________ 28 2. Installation and hook-up _________________________________ 30 2. 1 Water supply connection _____________________________________________________ 30 2. 2 Electrical connection ________________________________________________________ 31 3. Description of the controls _______________________________ 32 3. 1 Front panel ________________________________________________________________ 32 3. 2 Information display__________________________________________________________ 32 3. 3 Washing programs__________________________________________________________ 35 4. [. . . ] Each time the salt container is refilled, make sure that the cap is securely closed. The mixture of water and detergent must never penetrate the salt container, as this would compromise the operation of the regeneration system. In the event of this occurring, the warranty will be invalidated. Only use regenerating salt specially formulated for domestic dishwashers. If using salt tablets, do not fill the container completely. Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system. When necessary, refill the regenerating salt container before starting the washing program. In this way, the excess saline solution will be immediately removed by the water; the prolonged presence of salt water inside the tank may lead to corrosion. · · · · Be careful not to confuse the salt and detergent packages; adding detergent to the salt container will damage the water softening system. 38 User instructions ADJUSTING THE WATER SOFTENING SYSTEM The dishwasher is equipped with an electronic device for adjusting the water softening setting according to the hardness of the water. To adjust the water softening setting, proceed as follows: TYPE "A" TYPE "B" · Press down the HALF LOAD (6) button for a few seconds until the bS symbol appears on the INFORMATION DISPLAY (7). Press the START/STOP (5) button to access the water softening settings (the current setting appears on the information display). Press the HALF LOAD (6) button again to select the desired hardness setting (h1, h2. . . Choose the value by referring to the "Water hardness table". Press the START/STOP (5) button to exit the set-up mode. · · · WATER HARDNESS TABLE WATER HARDNESS German Degrees (°dH) French Degrees (°dF) 0-4 0-7 5 - 15 8 - 25 16 - 23 26 - 40 24 - 31 41 - 60 32 - 47 61 - 80 48 - 58 81 - 100 SETTING . h 0 . h 1 . h 2 . h 3 . h 4 . h 5 Contact your local water board for information on the hardness of your water supply. 39 User instructions 4. 2 Using the rinse aid and detergent dispensers The detergent and rinse aid dispensers are situated on the inner part of the door: the detergent dispenser is on the left, and the rinse aid dispenser is on the right. With the exception of the SOAK program, before every washing cycle it is necessary to add the required amount of detergent to the detergent dispenser. The rinse aid, on the other hand, should only be added as required. ADDING THE RINSE AID The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining; it is automatically added to the water during the final rinse cycle, from the container situated on the inner side of the door. · · · · · Open the door. Rotate the container cap anticlockwise by 1/4 of a turn and remove it. Add the rinse aid until the container is full (approximately 140 cc). The optical level indicator on the side of the cap should be completely obscured. Refill the rinse aid when the optical level indicator becomes clear again, or when the rinse aid warning light illuminates. Replace the cover and turn it in a clockwise direction. Use a cloth to remove any spillage of rinse aid which might lead to the formation of excess foam. ADJUSTING THE RINSE AID DISPENSER SETTING The dishwasher is factory set for medium water hardness. However it possible to change the setting by turning the dispenser's selector to the desired position: the amount of rinse aid dispensed is proportional to the selector position. The setting must be increased when the washed dishes appear dull or have circular staining. · · · · · To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it. [. . . ] Troubleshooting The dishwasher is equipped with a self-diagnostics system that is capable of detecting and signalling a number of possible faults. In the event of a fault or malfunction, before calling the After-sales service centre, we suggest that you first consult the troubleshooting guide below. If the problem persists even after implementing the recommended solutions, call the After-sales service centre after having carried out the following: making a note of the message displayed by the self-diagnostics system; · unplug the power cord from the socket; · shut off the water supply tap; · TABLE OF FAULTS DETECTED BY THE SELF-DIAGNOSTICS SYSTEM FAULT DESCRIPTION The dishwasher's AQUASTOP anti-flooding system has been activated (only for models equipped with the device). To disable the AQUASTOP: switch off the dishwasher and then switch it back on again. [. . . ]