User manual SMEG PL4210EB

[. . . ] This user-friendly manual will provide answers to all your questions about use of the dishwasher. For any other information about use and maintenance of the dishwasher, read the enclosed manual carefully. USER INSTRUCTIONS: useful information is provided for the use of the washing programs and all the dishwasher's functions. User instructions 1. Description of the controls 1. 1 Front panel All the dishwasher controls are grouped on the front panel. 1 2 3 4 5 6 7 8 9 ON/OFF BUTTON SELECTION PROGRAM BUTTONS (P1. . . P5) 3/1 OPTION BUTTON DELAY PROGRAM BUTTON START/STOP BUTTON POWER ON LIGHT PROGRAM PHASE INDICATOR LIGHTS INFORMATION DISPLAY RECESSED DOOR HANDLE 1. 2 Information display The dishwasher is equipped with a practical DISPLAY which provides information on the programmed dishwasher functions. User instructions DURATION MINUTES PROGRAMME, NUMBER & SYMBOL LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS CONSUMPTION WATER LITRES (1) POWER KWh (2) 1 2 SOAK Pans and dishes awaiting a further wash Dishes with light dirt Wash immediately after use for dishes with normal dirt Cold prewash Wash at 38C Cold rinse Rinse at 68C Wash at 55C Cold rinse Rinse at 68C Dry Cold prewash Wash at 40C Wash at 55C Cold rinse Rinse at 68C Dry Wash at 70C 2 cold rinses Rinse at 70C Dry Cold prewash Wash at 45C Cold rinse Rinse at 68C Dry Cold prewash Wash at 55C Cold rinse Rinse at 68C Dry Cold prewash Wash at 50C Wash at 65C Cold rinse Rinse at 68C Dry Prewash at 45C Wash at 70C 2 cold rinses Rinse at 70C Dry (**) 5 13 13 0, 02 0, 70 1, 01 QUICK (**) 3 ECO (*) EN 50242 (**) 4 AUTO 40-60 Wash immediately after use for dishes with normal dirt Very dirty pans and dishes, even with dried-on dirt Dishes with normal dirt (***) (***) (***) 5 INTENSIVE (**) 17 1, 45 6 DELICATE (**) 16 0, 98 7 BIO Dishes with normal dirt (**) 16 1, 10 8 AUTO 60-70 Normally soiled dishes, including dried-on residue (***) (***) (***) 9 SUPER Very dirty pans and dishes, even with dried-on dirt (**) 20 1, 50 Only run the soak program with half loads. (*) Reference program as per EN 50242 standard. [. . . ] IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE, THERE IS A SOLENOID VALVE INSIDE THE WATER INTAKE HOSE. DO NOT CUT THE HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP INTO WATER. IN THE EVENT OF DAMAGE TO THE WATER INTAKE HOSE, DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER SUPPLY AND FROM THE WATER SUPPLY. IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM A QUICK TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW. IF THE DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE. THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE REGULATIONS IN FORCE CONCERNING SAFETY AND ELECTRICAL EQUIPMENT. ANY TECHNICAL CHECKS SHOULD BE CONDUCTED EXCLUSIVELY BY A TRAINED AND AUTHORISED TECHNICIAN: REPAIRS CARRIED OUT BY UNAUTHORISED PERSONS WILL INVALIDATE THE WARRANTY, AS WELL AS POSING A POTENTIAL HAZARD TO THE USER. The manufacturer declines all responsibility for damage to persons or property resulting from failure to observe the above precautions, from tampering with even a single component of the appliance, or from the use of non original spare parts. 21 Installation instructions 2. Installation and hook-up Remove the polystyrene basket retainers. Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance. In these models, the cap of the salt container contains a green float which descends as the salt concentration in the water drops. When the green float can no longer be seen through the transparent cap, the container must be topped up with regenerating salt. The container is situated at the bottom of the dishwasher. After removing the lower basket, unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher. Before replacing the cap, remove any salt residues from around the opening. When using the dishwasher for the first time, in addition to the salt it is also necessary to add one litre of water to the container. Each time the salt container is refilled, make sure that the cap is securely closed. The mixture of water and detergent must never penetrate the salt container, as this would compromise the operation of the regeneration system. In the event of this occurring, the warranty will be invalidated. Only use regenerating salt specially formulated for domestic dishwashers. If using salt tablets, do not fill the container completely. Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system. [. . . ] Reassemble filter A in its seat and carefully screw the water intake hose back into position. CLEANING THE SPRAY ARMS The spray arms can be easily removed for periodic cleaning of the nozzles, to prevent possible clogging. Wash them under running water and carefully replace them in their seats, checking that their rotary movement is in no way impeded. To remove the upper spray arm, unscrew locking ring R. CLEANING THE SPRAY ARM, TRAVELLING VERSION To remove the TRAVELLING spray arm, take hold of it and raise it to release both the spray arm and the pipe from the tank, then detach the spray arm from the pipe. Wash both the pipe and the spray arm in running water, re-attach the spray arm to the pipe and return the assembly to the seat provided in the tank. [. . . ]