User manual SMEG PMO800AO8

[. . . ] 7 3. 2 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. 3 Room ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. 4 Extraction of the combustion products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. 5 Connection to gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Place the rubber tube D on connector A and fix it with clip E conforming to the regulations in force. 9 Instructions for the installer 4. ADAPTATION TO DIFFERENT TYPES OF GAS Before carrying out the following operations, disconnect the appliance from the electricity supply. The appliance is preset for natural gas G20 (2H) at a pressure of 20 mbar. In the case of operation with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps. To change the nozzles, proceed as described in the following paragraphs. 4. 1 Replacement of the cooking hob nozzles 1 Extract the pan stands and remove all the caps and flame-spreader crowns; 2 Unscrew the burner nozzles with a 7 mm socket wrench; 3 Replace the burner nozzles according to the type of gas to be used (see paragraphs "4. 2 Burner and nozzle characteristics table (60 cm model)" and "4. 3 Burner and nozzle characteristics table (90 cm model)"). 4 Replace the burners in the correct position. The nozzles for using town gas (G110 ­ 8 mbar) are available from authorised service centres. 10 Instructions for the installer 4. 2 Burner and nozzle characteristics table (60 cm model) Burner Rated heating capacity (kW) Nozzle diameter 1/ 100 mm 50 65 100 87 87 LIQUID GAS ­ G30/G31 28/37 mbar By-pass Reduced Capacity 1/100 capacity g/h G30 mm (W) 30 400 76 33 500 127 65 1600 284 50 900 233 211 Capacity g/h G31 75 125 279 229 207 Auxiliary Semi-rapid Ultra-rapid Oven Grill 1. 05 1. 8 3. 9 3. 2 2. 9 Rated heating capacity (kW) Burner NATURAL GAS ­ G20 20 mbar Nozzle diameter 1/100 mm 72 (X) 97 (Z) 135 (K) 130 130 Reduced capacity (W) 400 500 1600 900 - Auxiliary Semi-rapid Ultra-rapid Oven Grill 1. 05 1. 8 3. 9 3. 2 2. 9 11 Instructions for the installer 4. 3 Burner and nozzle characteristics table (90 cm model) Burner Rated heating capacity (kW) Nozzle diameter 1/100 mm 50 65 85 100 110 100 LIQUID GAS ­ G30/G31 28/37 mbar By-pass Reduced Capacity 1/100 mm capacity (W) g/h G30 30 33 45 65 59 400 500 800 1600 1300 76 127 218 284 378 291 Capacity g/h G31 75 125 214 279 371 286 Auxiliary Semi-rapid Rapid Ultra-rapid Oven Grill 1. 05 1. 8 3. 0 3. 9 5. 2 4. 0 Rated heating capacity (kW) Burner NATURAL GAS ­ G20 20 mbar Nozzle diameter 1/100 mm 72 97 115 135 164 150 Reduced capacity (W) 400 500 800 1600 1300 - Auxiliary Semi-rapid Rapid Ultra-rapid Oven Grill 1. 05 1. 8 3. 0 3. 9 5. 2 4. 0 12 Instructions for the installer 4. 4 Arrangement of the burners on the cooking hob BURNERS 1. Ultra-rapid 4. 5 Adjustment of oven burner To adjust the oven burner you need to open the oven door and carry out the following operations: · Remove the oven basin and its rack. · Lift up the oven surface and pull it outwards. 4. 5. 1 Replacing the oven and grill burner nozzles · Loosen the oven burner fixing screw A. · Push burner B towards the right until the nozzle is accessible. · Using a 13 socket wrench, replace the nozzle, inserting a new nozzle suitable for the type of gas to be used (see paragraphs "4. 2 Burner and nozzle characteristics table (60 cm model)" and "4. 3 Burner and nozzle characteristics table (90 cm model)"). 4. 5. 2 Primary air adjustment for the oven and grill burners · Loosen adjustment screw "A" of the air regulation sleeve. ) and minimum ( TIMER KNOB In order to use the timer, the buzzer must be set by turning the knob in a clockwise direction. The numbers correspond to minutes (maximum 55 minutes). Adjustment is progressive and intermediate positions between the figures can be used. The end of cooking buzzer does not interrupt operation of the oven. GAS GRILL AND GAS OVEN THERMOSTAT KNOB This knob allows the gas burner and the gas grill inside the oven to be lit. The cooking temperature of the gas oven is selected by turning the knob anticlockwise to the desired setting, between Min. Cooking can be carried out with the gas grill by turning the knob to position . To find out how to light the gas oven, see paragraph "8. 3 Using the gas oven". To find out how to light the gas oven, see paragraph "8. 4 Using the gas grill". 15 Instructions for the User 2-FUNCTION SELECTION KNOB This control lets you access the various functions of the oven. The illumination function ( ) can be used when the oven is switched off. However, the fan-assisted function ( ) can only be used if the lower burner of the gas oven is lit. The fan will start operating when the oven has reached a temperature of about 120-130°C. [. . . ] These residues are usually caused by the pan base rubbing against the pan stand and are difficult to remove with normal cleaning. Using abrasive or excessively aggressive products to clean the pan stand could damage its enamel surface. 23 Instructions for the User 10. 2. 2 Burner caps and flame spreader crowns For easier cleaning, the caps and the flame spreader crowns can be removed; wash them with warm water and a non-abrasive detergent making sure to remove any encrustation and wait until they are perfectly dry. WARNING: never wash these parts in a dishwasher. They can be left to soak in warm water and detergent. [. . . ]