User manual SMEG PS906-5

[. . . ] Contents 1 Instructions 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 General safety instructions Manufacturer liability Appliance purpose Identification plate This user manual Disposal How to read the user manual 36 36 39 39 39 39 40 41 2 Description 2. 1 General Description 2. 2 Symbols 2. 3 Available accessories 42 42 42 43 3 Use 3. 1 Instructions 3. 2 First use 3. 3 Using the hob 44 44 44 44 4 Cleaning and maintenance 4. 1 Instructions 4. 2 Cleaning the appliance 47 47 47 5 Installation 5. 1 5. 2 5. 3 5. 4 5. 5 5. 6 5. 7 Safety instructions Positioning in the counter top Mounting Gas connection Adaptation to different types of gas Electrical connection Instructions for the installer 49 49 49 53 54 59 64 65 These instructions apply only for the destination countries listed on the appliance’s data plate. This is a class 3 built in hob. We advise you to read this manual carefully, which contains all the instructions for maintaining the appliance’s aesthetic and functional qualities. For further information on the product: www. smeg. com 35 EN Instructions 1 Instructions 1. 1 General safety instructions Risk of personal injury • During use the appliance and its accessible parts become very hot. Never touch the heating elements during use. [. . . ] The appliance is equipped with an electronic ignition device. Simply press the knob and turn it anti-clockwise to the maximum flame symbol, until the burner ignites. If the burner does not light in the first 15 seconds, turn the knob to and wait 60 seconds before trying again. After lighting, keep the knob pressed in for a few seconds to allow the thermocouple to heat up. The burner may go out when the knob is released: In this case, the thermocouple has not heated up sufficiently. Wait a few moments and repeat the operation. In case of an accidental switching off, a safety device will be tripped, cutting off the gas supply, even if the gas cock is open. Return the knob to and wait at least 60 seconds before lighting it again. 44 Use Positioning the pan support grids The pan support grids are provided unassembled on the hob. To position the pan support grids correctly, follow the instructions shown in figure. Practical tips for using the hob For better burner efficiency and to minimise gas consumption, use pans with lids and of suitable size for the burner, so that the flames do not reach up the sides of the pan. • Do not use rough or abrasive materials or sharp metal scrapers. • Do not wash removable parts such as the hob pan support grids, flamespreader crowns and burner caps in the dishwasher. Food stains or residues Do not use steel sponges and sharp scrapers as they will damage the surface. Use normal, non-abrasive products and a wooden or plastic tool, if necessary. Rinse thoroughly and dry with a soft cloth or a microfibre cloth. Cooking hob pan support grids Remove the pan support grids and clean them in lukewarm water and non-abrasive detergent. Dry them thoroughly and return them to the hob. The continuous contact between the pan supports and the flame can cause modifications to the enamel over time in those parts exposed to heat. This is a completely natural phenomenon which has no effect on the operation of this component. 4. 2 Cleaning the appliance To keep the surfaces in good condition, they should be cleaned regularly after use. Ordinary daily cleaning Always and only use specific products that do not contain abrasives or chlorine-based acids. Pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or a microfibre cloth. 47 EN Cleaning and maintenance Flame-spreader crowns and burner caps For easier cleaning, the flame-spreader crowns and the burner caps can be removed. Wash them in hot water and nonabrasive detergent. [. . . ] • Disconnect the mains power supply. • Do not pull the cable to remove the plug. • Use cables withstanding a temperature of at least 90°C. • The tightening torque of the screws of the terminal supply wires must be 1. 5 2 Nm. [. . . ]