User manual SMEG PX140NLK

[. . . ] Contents 1 Instructions 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 General safety instructions Manufacturer’s liability Appliance purpose Identification plate This user manual Disposal How to read the user manual 28 28 31 31 31 31 32 33 2 Description 2. 1 General Description 2. 2 Symbols 34 34 34 3 Use 3. 1 Instructions 3. 2 First use 3. 3 Using the hob 35 35 35 35 4 Cleaning and maintenance 4. 1 Instructions 4. 2 Cleaning the appliance 39 39 39 5 Installation 5. 1 5. 2 5. 3 5. 4 5. 5 5. 6 5. 7 Safety instructions Section cut from the countertop Mounting Fastening with brackets Gas connection Adaptation to different types of gas Electrical connection 41 41 41 42 43 44 46 50 These instructions apply only for the destination countries listed on the appliance’s data plate. This is a class 3 built in hob. We advise you to read this manual carefully, which contains all the instructions for maintaining the appliance’s aesthetic and functional qualities. For further information on the product: www. smeg. com 27 EN Instructions 1 Instructions 1. 1 General safety instructions Risk of personal injury • During use the appliance and its accessible parts become very hot. Never touch the heating elements during use. [. . . ] Improper use Risk of damage to surfaces • Do not use aluminium foil to cover the burners or hob body. • Cookware should be placed inside the perimeter of the hob. • All pans must have smooth, flat bottoms. • If any liquid does boil over or spill, remove the excess from the hob. 3. 2 First use 1. Remove any protective film from the outside or inside of the appliance, including accessories. Remove any labels (apart from the technical data plate) from accessories. Remove and wash all the appliance accessories (see 4 Cleaning and maintenance). 3. 3 Using the hob All the appliance’s control and monitoring devices are located together on the front panel. The appliance is equipped with an electronic ignition device. Simply press the knob and turn it anti-clockwise to the maximum flame symbol, until the burner ignites. If the burner does not light in the first 15 seconds, turn the knob to and wait 60 seconds before trying again. After lighting, keep the knob pressed in for a few seconds to allow the thermocouple to heat up. The burner may go out when the knob is released: In this case, the thermocouple has not heated up sufficiently. Wait a few moments and repeat the operation. In case of an accidental switching off, a safety device will be tripped, cutting off the gas supply, even if the gas cock is open. Return the knob to and wait at least 60 seconds before lighting it again. 35 EN Use When the burner is lit, the relative activation knob will light up to indicate this. The knob will turn off a few seconds after it is turned to the position or if the burner goes out accidentally. If this happens, repeat the procedure holding the knob down for longer. Correct positioning of the pan supports Under the pan supports there are silicone rests with a hole that must be centred onto the matching fixing pins on the surface. If you notice that a pan is particularly unstable, make sure that the pan supports have been positioned correctly. Make sure that the pan supports are simply centred on their respective burners, without forcing them to be raised or tilted. If they are, repeat the positioning procedure. 36 Use Installing the pan supports The pan supports are provided unassembled on the hob. • Never use the griddle for more than 40 minutes. 38 Cleaning and maintenance 4 Cleaning and maintenance 4. 1 Instructions Improper use Risk of damage to surfaces • Do not use steam jets to clean the appliance. • Do not use cleaning products containing chlorine, ammonia or bleach on parts made of steel or that have metallic surface finishes (e. g. • Do not use rough or abrasive materials or sharp metal scrapers. [. . . ] Adjust the air flow by moving the air regulator B to obtain the distance D given in the corresponding table (see “Burner and nozzle characteristics tables”). After adjusting each burner, reassemble the appliance correctly. 48 Installation Adjusting the minimum setting for LPG Tighten the screw located at the side of the valve stem clockwise all the way. Following adjustment to a gas other than the one originally set in the factory, replace the gas setting label on the appliance with the one corresponding to the new gas. The label is inserted inside the nozzle pack (where present). [. . . ]