User manual SMEG S134AEBHK

[. . . ] Operating instructions ____________________________________ 34 4. 1 4. 2 4. 3 4. 4 Using the water softening system ______________________________________________ 34 Using the rinse aid and detergent dispensers _____________________________________ 36 General warnings and recommendations ________________________________________ 38 Using the baskets___________________________________________________________ 39 5. Cleaning and maintenance ________________________________ 42 5. 1 General warnings and recommendations ________________________________________ 42 6. Troubleshooting ________________________________________ 45 Thank you for choosing this product. We advise you to carefully read all the instructions contained in this manual, in order to understand how to operate your dishwasher safely and correctly. [. . . ] Do not carry out any preliminary rinsing. If available, connect the dishwasher to a hot water supply up to 60°C. When possible, skip the drying cycle by leaving the door open when the washing cycle is complete; the air and the residual heat will dry the dishes perfectly. TO CUT DOWN ON DETERGENT CONSUMPTION!AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity, observe the following: · separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures; · do not pour the detergent directly on the dishes. REMOVING THE DISHES At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket. 33 User instructions 4. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: · Adjust the water softening system; · Add the regenerating salt; · Add the rinse aid and detergent. 4. 1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness 41-60°dF ­ 24-31°dH). SALT When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. The salt container can hold approximately 1. 7 Kg of salt in grains. The container is situated at the bottom of the dishwasher. Then use a screwdriver to rotate the rinse aid selector to the desired position. The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains. If, on the other hand, the dishes are sticky or have white streaks, it is necessary to reduce the rinse aid setting. 36 User instructions ADDING THE DETERGENT To open the detergent dispenser cap, lightly press the button P. Add the detergent and close the cap carefully. During the washing cycle, the dispenser will be opened automatically. · When a SUPER program is selected, in addition to the normal dose of detergent, it is necessary to add an additional amount inside compartment G or H. Use only detergents specially formulated for dishwashers. For optimal washing results it is important to use a good quality detergent. The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results. Once opened the detergent packs should not be kept for too long, otherwise the detergent loses its effectiveness. Do not use detergents formulated for washing dishes by hand, because they produce a great deal of foam and may negatively affect the operation of the dishwasher. An insufficient amount of detergent will result in a partial removal of dirt from the dishes, whereas an excessive amount is wasteful and does not improve the washing results. [. . . ] Periodically (once or twice a year) it is advisable to clean the tank and gaskets, using a soft cloth and water to remove any deposits. CLEANING THE WATER INTAKE FILTER The water intake filter A located at the outlet of the water supply tap needs to be cleaned periodically. After having closed the water supply tap, unscrew the end of the water intake hose, remove the filter A and clean it delicately under running water. Reassemble filter A in its seat and carefully screw the water intake hose back into position. CLEANING THE SPRAY ARMS The spray arms can be easily removed for periodic cleaning of the nozzles, to prevent possible clogging. [. . . ]