User manual SMEG S341A

[. . . ] Operating instructions ____________________________________ 34 4. 1 4. 2 4. 3 4. 4 Using the water softening system ______________________________________________ 34 Using the rinse aid and detergent dispensers _____________________________________ 36 General warnings and recommendations ________________________________________ 38 Using the baskets___________________________________________________________ 39 5. Cleaning and maintenance ________________________________ 42 5. 1 General warnings and recommendations ________________________________________ 42 Thank you for choosing this product. We advise you to carefully read all the instructions contained in this manual, in order to understand how to operate your dishwasher safely and correctly. The manual is divided into paragraphs, which provide a step by step description of the dishwasher functions, with clear instructions accompanied by detailed illustrations. [. . . ] · The baskets have been correctly loaded. · The spray arms are able to rotate freely and without obstruction. · The dishwasher door is securely closed. CANCELLING THE CURRENT PROGRAM To cancel the program in progress the dishwasher must be switched off by pressing the ON/OFF key (3) (see section "3. Turn the program selector to SOAK and wait for the dishwasher to start. On completion of the program, switch off the dishwasher by pressing the ON/OFF key (3). Switch off the dishwasher by pressing the ON/OFF key (3) (see section "3. REMOVING THE DISHES At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket. 33 User instructions 4. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: · Adjust the water softening system; · Add the regenerating salt; · Add the rinse aid and detergent. 4. 1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness 41-60°dF ­ 24-31°dH). SALT When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. However it possible to change the setting by turning the dispenser's selector to the desired position: the amount of rinse aid dispensed is proportional to the selector position. The setting must be increased when the washed dishes appear dull or have circular staining. · · · · · To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it. Then use a screwdriver to rotate the rinse aid selector to the desired position. The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains. If, on the other hand, the dishes are sticky or have white streaks, it is necessary to reduce the rinse aid setting. ADDING THE DETERGENT To open the detergent dispenser cap, lightly press the button P. Add the detergent and close the cap carefully. During the washing cycle, the dispenser will be opened automatically. 36 User instructions · Use only detergents specially formulated for dishwashers. For optimal washing results it is important to use a good quality detergent. The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results. Once opened the detergent packs should not be kept for too long, otherwise the detergent loses its effectiveness. Do not use detergents formulated for washing dishes by hand, because they produce a great deal of foam and may negatively affect the operation of the dishwasher. [. . . ] Proceed as follows Pull-out version: · pull out the right-hand basket guide; · remove the stop, first releasing it as shown in the diagram; · push the guide to free the wheels; · fit the upper or lower pair of wheels into the guide, depending on the setting required; · return the stop to its original position. Push-button version: · pull out the basket to its limit position and pull the right side upwards. At this point it is possible to load larger sized plates into the lower basket. · To return to the original position, pull out the upper basket again and press the release lever. 41 User instructions 5. Cleaning and maintenance Before carrying out any work, always disconnect the appliance from the electrical power supply. 5. 1 General warnings and recommendations Avoid the use of acidic or abrasive detergents. [. . . ]