User manual SMEG S950X

[. . . ] INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING-UP OF FOOD. THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE. DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. [. . . ] PILOT LIGHT (GREEN) This light comes on when any of the oven elements is receiving power. HOB CONTROL KNOB Permits to adjust cook top heating. Rotate clockwise to set to desired value (2 to 12). HOB CONTROL KNOB WITH DUAL ZONES Used to select heating zone in plates with dual heating zones. Rotating the knob clockwise from between 2 to 12 heats the inner zone within the small diameter. Setting knob to or and releasing it (knob returns to 12) causes both zones to be heated. To adjust heat intensity, turn the knob anticlockwise to the desired value. To return to heating inside the inner zone only, set knob first to 0 and then to any value between 2 and 12 as desired. 35 Instructions for the user 3. 2 Electronic Analogue Clock LIST OF FUNCTIONS MINUTE-MINDER BUTTON AUTOMATIC SWITCH-OFF TIMING BUTTON TIME SETTING AND RESET VALUE DECREASE BUTTON VALUE INCREASE BUTTON 3. 2. 1 Setting the time When the oven is used for the first time, or after a power blackout, the display flashes on and off at regular intervals. Press the key for 1/2 seconds to stop the display flashing and start setting of the current time. Press the value modification keys or to increase or decrease by one minute for each time a key is pressed. Press one of the two value modification keys until the current time appears. The clock will start from the time set 6/7 seconds after the last key is pressed. At the end of each programmed cooking operation, the clock gives 8 beeps, repeated 3/4 times at intervals of about 1 and a half minutes. To reset the entire program set, keep the central key pressed for 1 or 2 seconds: if cooking has already started the oven will have to be switched off by hand. The image on the right shows an example of programming: the current time is 7. 06 and cooking is programmed to start at 8 o'clock and finish at 9. At 8 o'clock, the inside segments between 8 and 9 will start to flash and the hour pointer will remain still. Caution: for the oven to start cooking after the programming procedure just described, the thermostat and function selector must be properly set on the temperature and function required. 3. 2. 4 "DEMO" Function Models with analogue/digital programmer feature a "DEMO" function which deactivates the heating elements while leaving the other functions unchanged. To activate it, simply press the , , and keys and keep them held down for 3-4 seconds. A confirmation buzzer will inform the user that the function is active. When the "DEMO" function is active, the number 6 on the clock flashes at regular intervals. To deactivate it, simply repeat the same procedure. 39 Instructions for the user 4. Keep the oven door closed during cooking 6. 1 Traditional cooking (multifunction models) FUNCTION SWITCH THERMOSTAT SWITCH 50 ÷ 250°C This traditional cooking method, in which heat comes from above and below, is suitable for cooking food on a single level. You have to preheat the oven until the set temperature is reached. [. . . ] Rinse thoroughly and dry with a soft cloth or leather. Do not allow residues of sugary foods (such as jam) to set inside the oven. If left to set for too long, they might damage the enamel lining of the oven. 7. 2 Cleaning of the oven (without self-cleaning panels) For best oven upkeep clean regularly after having allowed to cool. Take out all removable parts. 47 Instructions for the user · · · Clean the oven grill and side guides with hot water and non-abrasive detergent. [. . . ]